Operating a plate-and-frame filter press above its rated pressure can damage filter plates, overheat the hydraulic system, increase motor loads, and place additional stress on pumps and pipelines. In severe cases, excessive pressure may cause slurry to spray from the plate pack, deform machine components, or create safety risks for operators.
A filter press may involve several different pressure settings, including feed pressure, hydraulic closing pressure, and membrane squeezing pressure on membrane filter presses. These pressures serve different functions and must be controlled according to the equipment design and manufacturer specifications.
Filter Plate and Frame Deformation or Damage
Each filter plate and frame has a specified working pressure. When the feed pressure exceeds the equipment's rated limit, the pressure inside the filter chambers may exceed the load that the plates are designed to withstand. If the plate closing force is insufficient to resist the feed pressure, gaps may develop between adjacent plates, allowing slurry to leak or spray from the sealing surfaces.
Continuous overpressure, excessive feed rates, or uneven pressure distribution inside the chambers can also cause filter plates and frames to deform or crack. In severe cases, a filter plate may break. Blocked feed ports and restricted filtrate channels can create local pressure imbalances and increase the risk of plate damage.
Damaged filter plates require maintenance or replacement and may force the machine to stop operating. A sudden release of pressurized slurry can also injure personnel working near the equipment.
junyifilter.com+2
Hydraulic System Overheating and Accelerated Oil Degradation
In filter presses that use a hydraulic system to close the plate pack, excessive hydraulic closing pressure places additional loads on the hydraulic pump, cylinder, and control components.
When the hydraulic system operates under sustained high loads, or the relief valve continuously releases excess flow, energy losses generate heat and raise the hydraulic oil temperature. Excessive heat accelerates oil oxidation and changes its properties, including its color and viscosity. This can reduce lubrication performance and contribute to sticking valves, ageing seals, and wear on hydraulic components.
Prolonged operation at an unsuitable oil temperature also affects system stability and increases the risk of faults involving the hydraulic pump, cylinder, and control valves.
assets.danfoss.com+2
Increased Motor Load and Risk of Overheating
The feed pump motor and hydraulic power unit motor perform different functions in a plate-and-frame filter press. Abnormally high feed pressure or hydraulic pressure can increase the load on the corresponding drive equipment.
For example, the feed pump must deliver slurry against the required pressure, while the hydraulic power unit maintains the specified closing force on the filter plates. If the equipment operates beyond its design conditions for extended periods, the motors may draw more current and generate excessive heat.
Prolonged motor overload accelerates the ageing of internal insulation materials and shortens motor service life. Severe overload may also activate the motor's protection system or cause motor burnout, resulting in equipment downtime and production interruptions.
Additional Stress on Feed Pumps and Pipelines
Excessive feed pressure increases the pressure load on the pump casing, mechanical seals, pipelines, and pipe connections. If the pressure exceeds the rated limits of these components, seal failure, joint leakage, or pipeline damage may occur.
When the feed pump handles slurry containing solid particles, these particles can also cause erosion and wear on wetted components such as the impeller and pump casing. This type of wear is mainly related to particle characteristics, flow conditions, and the materials used for the pump's wetted components. It should not be attributed to excessive pressure alone.
Prolonged operation under unsuitable conditions can increase maintenance requirements and the cost of replacing pump and pipeline components.
Effects on Equipment Safety and Production Efficiency
When feed pressure is excessive and the plate closing force is insufficient, or the filter plate sealing surfaces are defective, slurry may leak or spray from between the plates. Operators may need to stop the machine, clean the spilled material, inspect the plate pack, and repair the fault. These operations increase unplanned downtime.
If the hydraulic system, filter plates, or pipelines have already sustained damage, continued operation may lead to further equipment failures. Operators should monitor pressure gauge readings, filter plate sealing conditions, and hydraulic system performance. Any abnormal pressure condition should be investigated and handled according to the equipment operating procedures.
Custom Machining for Filter Press Components
The reliable operation of a plate-and-frame filter press depends on the proper fit and performance of its mechanical components. Hansheng Automation provides drawing-based custom machining for non-standard components used in filter presses and related mechanical equipment. We support both single-piece manufacturing and small-batch precision machining.
Our machining services also cover components for other industries, including tobacco and packaging machinery, filling equipment, yacht equipment, and remote-controlled racing cars. Parts are manufactured according to customer drawings, dimensions, and assembly requirements.


