A fully automatic nonwoven fabric winding machine winds continuously produced fabric into rolls at a set tension and speed. During operation, the drive system rotates the main shaft and winding drum. As the roll diameter increases, the machine must adjust winding torque and rotational speed to keep the winding process synchronized with the upstream production equipment. Proper control helps prevent wrinkles and loosely wound rolls.
Working principles of a nonwoven fabric winding machine
During winding, the drive system rotates the main shaft and winding drum, allowing the fabric to wind layer by layer under the specified tension. As more material accumulates on the drum, the roll diameter increases. At a constant web tension, a larger roll diameter produces a higher torque requirement.
For this reason, the main shaft, internal components of the winding drum, and machine base must have sufficient strength, stiffness, and stability. The anchor bolts securing the base must also withstand the loads generated during operation.
Compared with an unwinding machine, a winding machine generally subjects its winding drum and main shaft to greater loads during the winding process. When designing the equipment, engineers need to consider the loads acting on each structural component under the actual winding conditions. Insufficient structural stiffness or unstable connections can affect machine operation.
Torque motor and winding speed control
A fully automatic winding machine can use a torque motor as its drive source. A torque motor has constant-power transmission characteristics, meaning its output torque and rotational speed vary inversely.
As the roll diameter increases, the winding system requires greater torque, while the rotational speed of the winding drum decreases accordingly. By adjusting the motor output to accommodate these changes, the machine can maintain a winding linear speed that matches the speed of the upstream production equipment, even as the roll diameter grows.
This speed coordination reduces differences between upstream production speed and winding speed, allowing continuous operation with less manual intervention.
When a winding machine operates alongside a circular loom or other upstream equipment, its speed must be adjusted to match the production speed of the preceding process. The specific control method depends on the production line's speed requirements and the characteristics of the material being wound.
Tension control requirements for automatic winding machines
Tension control directly affects the winding quality of nonwoven fabric, meltblown fabric, and film. The machine must adjust tension according to the roll diameter and operating conditions during startup, normal winding, and the final stage of winding. Incorrect tension can cause wrinkles or loosely wound rolls.
A fully automatic winding machine should meet the following requirements:
Stable winding tension: The control system should automatically adjust tension throughout the winding process according to the winding conditions, reducing the need for repeated manual adjustments.
Tension control during startup and at full roll diameter: Tension must not be too high when winding starts with an empty core, as this can cause wrinkles in film, meltblown fabric, or nonwoven fabric. As the roll approaches its full diameter, tension must not be too low, otherwise the material may wind too loosely.
Fast system response: When the machine accelerates or decelerates, or when upstream production speed and web tension change, the control system should respond promptly. This helps limit the effect of speed and tension fluctuations on winding quality.
Adjustable tension settings: Nonwoven fabric, meltblown fabric, and film have different winding tension requirements. The machine should allow tension values to be set according to the requirements of each production process.
These requirements must be coordinated with the motor drive, speed regulation, and machine operating parameters to accommodate different materials and production speeds.
Automatic winding, roll changing, and slitting
Depending on the production process, a nonwoven fabric winding machine can combine winding, automatic roll changing, and slitting in one integrated configuration. After continuous winding, the machine can perform roll changing and slitting to produce rolls of the required specifications. These finished rolls can then be prepared for packaging and transport.
Automation reduces the need for manual operations during winding, roll changing, and slitting. It also reduces repetitive work and labor input in the production process. The machine structure and control configuration should be determined according to the material width, required roll dimensions, and production line operating conditions.
Custom machining of components for nonwoven fabric winding machines
The operating stability of a winding machine also depends on the machining quality of components such as the main shaft, internal winding drum components, and base mounting parts. Different machines may have different mounting dimensions, connection methods, and structural requirements.
Hansheng Automation provides custom machining services based on customer-supplied drawings. We can manufacture non-standard components and support both single-piece and small-batch precision machining.
Our precision component machining services also cover applications beyond nonwoven fabric winding equipment. We manufacture custom components for filling machinery and tobacco packaging machinery, as well as precision structural parts for yachts and radio-controlled racing cars. Customers can provide part drawings and relevant machining requirements for us to assess the appropriate manufacturing process.


