What equipment is required for a PET strapping production line?

Nov 17, 2026 Leave a message

Nicole Li
Nicole Li
Leading the innovation team, Nicole focuses on researching and developing new products and technologies. Her work is instrumental in keeping Hansheng at the forefront of the automation industry.

 

A PET strapping production line consists of several processing sections, including raw material preparation, extrusion, cooling, stretching, embossing, heat setting and winding. In addition to the extruder, die, cooling equipment and winder, a complete line generally requires crystallizing and dehumidifying equipment, melt filtration units, haul-off rolls, heating ovens and heat-setting equipment.

The equipment configuration varies according to the raw material, production speed, strap dimensions and required output. Each section must operate in coordination to maintain dimensional consistency, mechanical strength and winding quality of the finished PET strapping.

PET raw material preparation equipment

Before entering the extruder, PET raw materials generally undergo crystallization, dehumidification and drying. The equipment typically includes a material conveying system, crystallizing dryer and dehumidifying dryer.

The crystallizing unit treats PET material to reduce the risk of pellets sticking together during subsequent heating. The dehumidifying and drying system removes moisture from the raw material. Excessive moisture in PET can cause hydrolysis during melt processing, reducing molecular weight and affecting processing stability and finished product properties.

For production lines using recycled PET bottle flakes or other recycled materials, additional pretreatment and conveying equipment may be required according to the condition of the feedstock.

Extrusion and forming equipment

The extrusion system mainly consists of an extruder, melt filtration unit, metering pump and extrusion die.

Extruder

The extruder heats, melts and conveys the dried PET material to the die. Driven by a motor, the screw rotates inside the barrel to transport, plasticize and mix the material, producing a continuous melt.

Depending on the raw material, production capacity and process requirements, the line may use either a single-screw or twin-screw extruder.

Melt filtration unit and metering pump

The melt filtration unit removes impurities from the molten PET, reducing the risk of contamination during subsequent forming and processing. The metering pump regulates the melt delivery rate and helps reduce fluctuations in extrusion output.

Some production lines also use a continuous screen changer to minimize interruptions when the filtration screens need replacement.

Extrusion die

The die is installed at the extruder outlet. It distributes and shapes the molten PET into a continuous strip blank with the required cross-section.

The die structure and flow channel design affect the width, thickness and cross-web dimensional consistency of the extruded strip. Its configuration must match the required PET strapping dimensions.

Cooling, forming and haul-off equipment

After passing through the die, the molten PET needs to be cooled to form a stable initial strip profile. This stage generally involves a cooling water tank, dewatering device and haul-off rolls.

Cooling water tank

The cooling tank usually uses water quenching to reduce the temperature of the hot strip blank after extrusion. This allows the material to form an initial stable profile.

Cooling conditions in the tank affect dimensional stability and the subsequent stretching process.

Dewatering and haul-off equipment

After leaving the cooling tank, the strip passes through a dewatering device to remove residual surface water. Haul-off rolls then transport the material to the heating and stretching sections at a controlled speed.

The haul-off speed must remain coordinated with the extrusion output to prevent the strip from becoming slack or undergoing excessive stretching during transport.

Heating and stretching equipment

Stretching is an important stage in PET strapping production. The cooled strip blank is reheated to a suitable processing temperature before passing through stretching rolls for longitudinal drawing and molecular orientation.

Preheating unit

The preheating unit generally uses a hot air circulation oven to bring the strip to the required temperature before it enters the stretching rolls.

Heating conditions must be adjusted according to the PET material and the specific stretching process.

Multi-stage stretching rolls

The stretching section generally consists of several groups of haul-off or stretching rolls. By controlling the speed difference between successive roll groups, the equipment applies controlled stretching and molecular orientation to the PET strip.

This process improves the strength and mechanical performance of the finished strapping.

Depending on the product dimensions and process requirements, the production line may use single-stage or multi-stage stretching arrangements.

Embossing unit

The embossing unit uses patterned rolls to create regular surface textures on the PET strapping. These patterns increase friction between the strap and the surfaces in contact with it, helping reduce slippage during bundling and transportation.

Embossing quality depends on the roll pattern, nip pressure and operating speed. The embossing unit can be positioned after stretching or at another suitable point in the production line, depending on the equipment layout. Its operating speed must remain synchronized with the strip feeding system.

Heat-setting and cooling equipment

After stretching and embossing, the PET strapping generally undergoes heat setting to stabilize its dimensions and material structure.

Heat-setting oven

The heat-setting oven generally uses hot air circulation to treat the stretched PET strapping under controlled temperature conditions. This process helps release some of the internal stress generated during stretching and reduces the risk of dimensional changes during subsequent use.

Cooling equipment

After heat setting, the strap needs further cooling before it enters the downstream conveying and winding sections. Depending on the production process, the line may use cooling water tanks, cooling rolls or other cooling equipment.

Winding equipment

The winder continuously winds the cooled and stabilized PET strapping into rolls for subsequent packaging, storage and transportation.

A winding unit generally includes a winding shaft, drive mechanism, tension control system and, where required, a traversing mechanism. During winding, the system must adjust winding speed and tension according to strip speed and changes in roll diameter. This helps prevent loose winding, telescoping and roll deformation.

Depending on production capacity and packaging requirements, the line may use a single-position or dual-position winder. Some configurations also include automatic roll changing and automatic weighing or counting functions to support continuous production.

Control system and auxiliary equipment

In addition to the main processing equipment, a PET strapping production line requires an electrical control system and supporting auxiliary equipment.

The PLC control system coordinates extrusion, cooling, haul-off, stretching, heat setting and winding. It also monitors equipment operating conditions and allows operators to adjust process parameters to keep the different sections synchronized.

Material conveying equipment, heating systems, cooling water circulation systems and other auxiliary facilities must also be selected according to the production line configuration.

Custom machining of components for PET strapping production equipment

A PET strapping production line contains multiple mechanical sections for extrusion, haul-off, stretching, embossing and winding. These sections require roller shafts, roll bodies, mounting bases, connecting components and other non-standard mechanical parts.

When standard components cannot meet specific equipment or assembly requirements, we can manufacture precision mechanical parts according to customer drawings. Both single-piece and small-batch machining are supported.

Hansheng Automation also provides custom machining services for components used in other industries, including tobacco and packaging machinery, filling equipment, printing machinery, yacht equipment and RC racing cars. Parts are manufactured according to customer drawings and individual machining requirements.

Mining--Metallurgical-Machinery