Gas pores inside continuously cast steel billets are generally associated with the gas content of molten steel, the moisture condition of alloy additions, and the drying of ladle and tundish refractories. During solidification, dissolved gases may be released from the molten steel and accumulate to form internal pores or blowholes.
When pores are distributed across the entire billet cross-section, steel quality and the alloy addition and degassing processes should be examined first.
Main causes of gas porosity in steel billets
Moisture in alloy additions
Ferroalloys, carburizers, and other additives used during steelmaking may introduce moisture into molten steel if they are not properly stored or dried before use. This moisture can increase the hydrogen content of the steel.
As molten steel cools and solidifies, the solubility of hydrogen in solid steel is significantly lower than in liquid steel. During solidification, dissolved gases become concentrated in the remaining liquid phase. When their concentration reaches a certain level, gas bubbles may form and become trapped within the billet.
The storage conditions, moisture content, and addition procedures for ferroalloys and other materials should therefore be checked to prevent damp materials from introducing hydrogen into the molten steel.
Insufficient drying of ladle linings and refractory materials
Ladle and tundish linings must be properly dried and heated before use according to the operating procedure. If refractory linings, other refractory materials, or sealing materials retain excessive moisture, contact with molten steel can introduce hydrogen into the metal.
Moisture in tundish refractories, covering materials, and ladle slag materials can also contribute to hydrogen pickup. Inspection should therefore cover not only ladle lining preparation but also tundish preparation, refractory storage, and drying procedures.
Excessive dissolved gas content in molten steel
High concentrations of dissolved hydrogen and nitrogen can contribute to gas pore formation. Carbon monoxide (CO), produced by the reaction between dissolved carbon and oxygen, can also form gas bubbles during solidification.
As molten steel solidifies, the solubility of gases differs significantly between the liquid and solid phases. The formation of the solidified shell causes some dissolved gases to become concentrated in the remaining liquid steel. When the local gas concentration reaches supersaturation, bubbles may nucleate in the interdendritic regions and become trapped in the billet.
In addition, air entrainment or secondary oxidation during tapping, ladle transfer, and pouring can increase the gas content of the molten steel. These operations should therefore be checked together with steel gas analysis and deoxidation practices.
Diagnosing the problem from pore distribution across the billet cross-section
The distribution of pores across a billet cross-section can help narrow down possible causes, but their location alone is not sufficient to identify the source of the defect.
When pores are distributed widely across the entire cross-section, priority should be given to checking the overall quality of the molten steel. Particular attention should be paid to hydrogen and nitrogen levels, deoxidation efficiency, and the moisture condition of alloy additions and refractory materials.
When pores are concentrated mainly in the center of the billet, they should be distinguished from centerline porosity, shrinkage cavities, and other solidification defects. Further checks should include steel composition, pouring temperature, withdrawal speed, and secondary cooling conditions. Examination of both transverse and longitudinal billet sections can help determine the type of defect.
For billets containing numerous or relatively large pores, macrostructural examination, metallographic analysis, and gas composition testing may be required to confirm the defect characteristics before deciding on process adjustments.
Basic production process of a continuous casting machine
Continuous casting is a process in which molten steel is directly converted into solid billets through continuous pouring and solidification.
During production, molten steel is continuously poured into a water-cooled copper mold. As the steel cools, an initial solidified shell forms along the mold wall. Once the shell reaches sufficient thickness to support the liquid steel inside, the strand is withdrawn from the mold by the withdrawal equipment.
The strand then enters the secondary cooling zone, where water sprays further reduce its temperature until the remaining liquid core gradually solidifies.
After cooling and straightening, the strand passes along the run-out roller table. Cutting equipment then cuts it into specified lengths according to downstream rolling requirements.
Compared with conventional ingot casting followed by primary rolling, continuous casting eliminates intermediate production stages, improves production efficiency and metal yield, and reduces energy consumption and manufacturing costs. Its continuous production process also allows billet quality to be controlled through process parameters and equipment operating conditions.
Continuous casting machines are now an important part of both integrated and electric steelmaking production lines.
Custom machining of components for continuous casting equipment
The manufacture and maintenance of continuous casting machines involve various mechanical structures and transmission components, including withdrawal roll shafts, guide roll shafts, bearing housings, mounting supports, and connecting parts. Different caster designs have specific requirements for component dimensions, geometry, and assembly accuracy.
We provide precision machining based on customer-supplied drawings and support both single-piece and small-batch orders. Hansheng Automation machines shafts, bearing support components, and other non-standard mechanical parts for steelmaking equipment and automated production lines.
Our precision machining services also cover other industries, including structural components for yacht equipment, precision parts for RC racing cars, tobacco packaging machinery components, and parts for filling machinery. We manufacture non-standard components according to customer drawings for different equipment applications.


