The feeding method for a sintering furnace depends on the material form, sintering process, and furnace design. For powdered and granular raw materials, common options include belt conveying, screw conveying, vibratory feeding, and pneumatic conveying. Manual loading may also be used in laboratory furnaces, small-batch production, or applications involving specially shaped workpieces.
These methods differ in conveying capacity, metering accuracy, sealing performance, and level of automation. Equipment selection should account for particle size, bulk density, flowability, moisture content, and furnace feeding requirements to ensure a consistent and stable material supply.
Belt Conveyor Feeding
Belt conveying is a common method for continuous material handling in industrial production. It is mainly used for granular, bulk, and certain powdered materials. A motor drives the conveyor pulleys, causing the belt to move continuously and transfer material from a storage hopper or upstream process to the furnace feeding point.
This method is suitable for production lines requiring relatively large conveying capacities and longer transport distances. Belt conveyors can also be combined with electronic belt scales and other weighing equipment for continuous conveying and proportioning.
The main design parameters include belt width, belt speed, conveying inclination, and conveying capacity. The operating speed must be selected according to particle size, bulk density, required throughput, and equipment configuration. A single speed range should not be applied to every project.
When handling powdered materials, dust control must also be considered. Enclosed conveyor structures and dust collection equipment at transfer points may be required, depending on operating conditions.
Screw Conveyor Feeding
A screw conveyor uses rotating screw flights to move materials along a trough or pipe. It is suitable for powders and granular materials and is commonly used for metered feeding and short-distance conveying upstream of a sintering furnace.
A typical screw conveyor consists of a drive motor, gear reducer, screw shaft, screw flights, trough or casing, and support components. The motor drives the screw shaft through the reduction gearbox. As the shaft rotates, the flights push the material toward the discharge end.
Screw conveyors have a compact structure and can be enclosed to limit dust emissions. For processes that require oxygen exclusion or protection against material oxidation, nitrogen sealing or an inert gas supply can be incorporated into the design.
However, screw conveyors are not suitable for every material. Highly cohesive materials, materials that tend to form lumps, and feedstock containing large foreign objects may cause material buildup, blockages, or jamming. Equipment selection must therefore consider material flowability, particle size, and moisture content, along with the required screw diameter, rotational speed, and flight geometry.
Vibratory Feeder Feeding
A vibratory feeder uses periodic vibration to move materials along a feeding trough. It can transfer powdered, granular, and small lump materials from a storage hopper to the next processing stage at a controlled and relatively uniform rate.
A typical vibratory feeder consists of a feeding trough, exciter, elastic supports, drive unit, and frame. During operation, the exciter generates directional vibration in the trough, moving the material toward the discharge end.
This method is suitable for production lines where uniform feeding is important. Vibratory feeders can be integrated with level sensors, weighing equipment, and automatic control systems to regulate the material supply rate.
The vibration amplitude and frequency must be selected according to material particle size, bulk density, flowability, and required throughput. A range of 0.5 to 8 mm should not be treated as a universal amplitude specification for all vibratory feeders.
During operation, the elastic supports, leaf springs, fasteners, and exciter bearings should be inspected regularly. Fatigue, loose connections, and abnormal vibration need to be addressed before they affect equipment performance.
Pneumatic Conveying
Pneumatic conveying uses an airflow to transport materials through enclosed pipelines. It is mainly used for powders and fine granular materials. Compared with mechanical conveying, it can reduce the need for intermediate transfer equipment and is suitable for longer distances, centralized feeding, or multi-point distribution systems.
Pneumatic conveying systems can be classified as positive-pressure or negative-pressure systems according to their operating pressure. They can also use dilute-phase or dense-phase conveying, depending on the gas-solid flow conditions.
Positive-pressure conveying: Compressed air or another conveying gas pushes the material through the pipeline. This arrangement is suitable for transferring material from one feeding point to multiple receiving points.
Negative-pressure conveying: A fan or vacuum unit creates negative pressure in the pipeline and draws material into the system. It is suitable for collecting material from several pickup points and conveying it to a central receiver.
Dilute-phase conveying: The gas velocity is relatively high, and the material is suspended and dispersed in the airflow.
Dense-phase conveying: The system operates with a lower gas velocity and suitable pressure conditions, allowing a higher concentration of material to move through the pipeline. It can be suitable for certain materials that are sensitive to particle breakage or wear.
The conveying pressure and gas velocity must be calculated according to particle size, density, flowability, conveying distance, and pipeline layout. A pressure range of 0.3 to 0.6 MPa should not be treated as a universal requirement for all pneumatic conveying systems.
For materials that are easily oxidized or present a fire or explosion hazard, the system must also account for oxygen concentration, static charge accumulation, and dust explosion characteristics. Depending on test results and the risk assessment, nitrogen or another inert gas may be used. Appropriate explosion protection, isolation, and pressure relief measures may also be required.
Manual Feeding
Manual feeding is mainly used for laboratory sintering furnaces, small-batch trials, and specially shaped workpieces that cannot be handled by conventional conveying equipment.
Operators load the raw materials or workpieces into trays, crucibles, or dedicated carriers, then place them into the furnace through the loading door or a designated feed opening. This method requires relatively little equipment and provides flexibility for batch processing.
However, throughput and feeding consistency depend heavily on the loading method, material weight, and handling time. Manual feeding is generally unsuitable for large-scale continuous production.
Operators should use appropriate heat-resistant protective equipment based on the furnace opening temperature and material conditions. Suitable loading tools and protective devices are also necessary to prevent contact with hot surfaces and exposure to thermal radiation. For sintering processes that require a controlled furnace atmosphere, opening the furnace door must be managed to limit air ingress and temperature fluctuations.
Workpiece Conveying Methods for Continuous Sintering Furnaces
The methods described above mainly apply to the conveying of powdered and granular raw materials. When a furnace processes compacted powder metallurgy parts, ceramic green bodies, or other shaped workpieces, the products are generally placed on carrier plates or in saggers and moved through the furnace by a mechanical conveying system.
Common arrangements include:
Mesh belt conveying: A heat-resistant metal mesh belt continuously carries workpieces through the furnace. It is commonly used in continuous sintering production lines.
Roller hearth conveying: Heat-resistant rollers move carrier plates or workpieces through the furnace. This arrangement is suitable for certain product dimensions and shapes.
Pusher-type conveying: Workpieces are loaded into saggers or trays. A mechanical or hydraulic pusher advances the push plates and carries the loads through the furnace according to a set operating cycle.
Walking beam conveying: Movable beams lift and advance carrier plates in a stepwise sequence, transferring the workpieces through the furnace. This arrangement is used in continuous furnaces with suitable structural designs.
These are workpiece conveying systems inside the furnace. They are different from the belt, screw, and pneumatic conveying equipment used to feed raw materials into a batching or preparation system. The choice depends on workpiece dimensions, load weight, sintering temperature, and production cycle.
Factors to Consider When Selecting a Sintering Furnace Feeding Method
The feeding method should be selected according to the production process, raw material properties, and furnace design.
Material size and form: Powders and fine particles can be handled by screw conveyors or pneumatic systems. Bulk and larger granular materials are generally better suited to belt conveyors or vibratory feeders.
Throughput and metering accuracy: Continuous high-volume production requires sufficient conveying capacity. Electronic belt scales, screw weigh feeders, or other metering devices may be needed to control material proportions.
Material flowability: Materials that tend to form lumps, adhere to equipment, or bridge in storage hoppers may require anti-bridging devices, agitators, or other anti-blockage measures.
Furnace atmosphere requirements: Materials that are susceptible to oxidation may require sealed feeding arrangements, inert gas protection, and control of the furnace atmosphere during loading.
Safety and maintenance: Combustible dust hazards must be evaluated through appropriate testing and risk assessment. The required protection measures should then be selected according to the material and equipment design.
A suitable feeding system must provide the required conveying capacity while maintaining consistent feed, accurate metering, and reliable operation.
Custom Machining for Sintering Equipment
Sintering furnaces can use belt conveyors, screw conveyors, vibratory feeders, pneumatic conveying, or manual loading, depending on the material and production process. Continuous furnaces that process shaped workpieces may also use mesh belts, roller hearths, pushers, or walking beam systems. The final equipment configuration depends on material properties, sintering temperature, furnace atmosphere, and production cycle.
For components used in sintering equipment and associated conveying machinery, we provide custom precision machining based on customer-supplied drawings. Hansheng Automation also manufactures non-standard parts for tobacco packaging machinery and filling machinery, as well as precision components for yacht equipment and radio-controlled racing cars. We support single-piece and small-batch production according to component drawings and assembly requirements.


