Wet scraper conveyors for grate siftings collect and transport fine ash that falls through the gaps in an incinerator grate. These conveyors commonly use a water-seal design. Fine ash enters the conveyor, mixes with water, and is then carried toward the discharge channel by the scraper chain.
During operation, fine ash mixed with water can form a sticky slurry. When this material accumulates near the discharge outlet or inside the conveyor, heat radiation and hot air from nearby areas can cause the water to evaporate. The remaining solids then harden and form deposits. Waste composition, the amount of leachate entering the system, water seal level, and flushing conditions also affect deposit formation.
To prevent buildup, the material characteristics and equipment structure must be considered together. Effective measures include improving flushing arrangements, maintaining the water seal, modifying areas prone to deposits, and providing suitable blockage removal facilities.
Main Causes of Buildup in Wet Grate Siftings Conveyors
Buildup in a wet grate siftings conveyor is rarely caused by a single factor. It generally results from the accumulation of fine ash, changes in moisture content, material adhesion, and localized heating.
Fine Ash and Water Forming Slurry
Fine ash, partially burned particles, and other small residues fall through the grate openings during incineration. When these materials enter the wet scraper conveyor, they mix with the water and form a solid-liquid slurry.
If the slurry has poor flowability or accumulates in dead zones near the discharge outlet, fine ash can settle on the conveyor bottom, sidewalls, and discharge passage. Continued accumulation gradually increases the deposit thickness, interfering with scraper movement and normal ash discharge.
Slurry Hardening Under Localized Heat
The discharge section of a wet grate siftings conveyor may be located close to the high-temperature ash discharge channel at the end of the grate.
Slurry can adhere to surfaces around the discharge outlet. When exposed to hot flue gas or heated air, its moisture gradually evaporates and the remaining solids become harder.
Without timely flushing, repeated deposition and drying can produce a dense layer of hardened ash. Severe buildup may block the discharge opening and prevent the conveyor from operating normally.
Leachate and High-Moisture Waste Increasing Sediment Accumulation
During rainy periods or when incoming waste has a high moisture content, more water and leachate may enter the incineration system. Fine ash, soil, and other suspended particles mix with these liquids, changing the solids concentration and flow characteristics of the slurry.
If the drainage and flushing capacity is insufficient, the mixture may accumulate near pneumatic baffles, hopper bottoms, water-seal areas, and other low points or joints.
Waste Composition Increasing Material Adhesion
Certain mixed construction wastes, aged waste, and materials containing large amounts of soil, ash, or calcium-bearing mineral components can increase the fine particle and mineral content of the grate siftings.
When these materials mix with water, they may form deposits with poor flowability. Depending on the waste composition and local conditions, some materials may agglomerate or harden. Buildup often starts at joints between the bottom plate, side plates, and connecting structures before spreading to a larger area.
Moisture and Fine Ash Accumulating in the Water-Seal Area
The water-seal section of a wet scraper conveyor is continuously exposed to cooling water and fine ash. Water vapor may form near the water surface, while condensation and moisture deposits may develop on the internal walls.
When ash-containing moisture adheres to the inner walls or conveyor trough and is later exposed to hot air or heat radiation from nearby equipment, the water evaporates and the remaining ash hardens.
Some lightweight fine ash may also remain suspended in the water or float on the surface. It can accumulate near the feed openings, hopper outlets, and water-seal structures, increasing the risk of local blockage.
Solutions for Buildup in Wet Grate Siftings Conveyors
Different measures are required depending on the location and cause of the deposits. Simply increasing the water supply does not necessarily solve the problem. Accumulated material must also be removed effectively.
Installing Spray Flushing at the Discharge Outlet
When slurry hardening occurs near the discharge outlet, a flushing water pipe can be installed inside the conveyor casing, above the discharge opening. Multiple spray nozzles can be arranged along the pipe and directed toward areas where ash tends to accumulate.
The spray system can be connected to a clean water supply through a control valve. Flushing can be initiated at timed intervals or automatically according to the conveyor's operating conditions.
Nozzle direction, spray coverage, and water pressure must be selected according to the outlet geometry. The spray should reach the areas requiring cleaning without directly exposing mechanical components that are not designed for water contact.
Chinese utility model patent CN218154236U describes a similar arrangement for a wet scraper conveyor used in waste incineration. It uses a horizontal water pipe above the discharge outlet, fitted with multiple high-pressure nozzles directed toward the outlet. A solenoid valve controls timed flushing. This provides a design reference for preventing slurry hardening and blockage near the discharge section.
Improving the Water-Seal and Flushing System
A wet grate siftings conveyor must maintain an appropriate water level. The water seal needs to prevent uncontrolled air leakage through the ash hopper outlets while also supporting ash cooling and conveying.
The following components should be checked during equipment modifications:
Water-seal makeup system: Adjust the water supply controls to maintain a relatively stable level and prevent loss of the seal.
Spray piping: Arrange the nozzles properly and install filters where required to reduce nozzle blockage caused by suspended impurities.
Flushing valves: Use pneumatically or electrically actuated valves to provide timed, staged, or interlocked flushing and reduce dependence on manual operation.
Drainage system: Inspect the outlets and drain lines for accumulated ash, blockage, and poor drainage.
Water-seal overflow arrangement: Where small-diameter overflow pipes are prone to blockage, an overflow trough or weir may be considered, depending on the equipment design. This can make floating ash removal and cleaning easier.
Flushing flow and drainage capacity must be balanced. Excessive flushing must not lower the water level enough to break the seal or affect furnace isolation.
Modifying the Conveyor and Discharge Structure
When buildup repeatedly occurs in the same location, the equipment structure should be inspected rather than relying only on increased flushing water.
Possible modifications include:
Reducing dead zones at the joints between the discharge outlet, bottom plate, and side plates to limit ash retention.
Adjusting the bottom plate and discharge passage to improve slurry movement and reduce accumulation.
Improving the pneumatic baffle and surrounding sealing structure to prevent repeated ash buildup above the baffle.
Checking whether the scraper chain has sufficient conveying capacity for the amount and characteristics of the grate siftings.
Improving insulation or thermal protection around the discharge section to reduce rapid moisture evaporation and slurry hardening.
For equipment in long-term service, the wear condition of the scraper flights, chains, guide rails, and drive components should also be inspected. Damaged parts should be replaced when necessary.
Installing Anti-blockage and Mechanical Cleaning Devices
Inspection openings, cleanout ports, or dedicated clearing devices can be installed at the bottom ash hoppers, conveyor inlets, and other locations where deposits frequently accumulate.
When a local blockage occurs, dedicated mechanical tools can be used to remove the deposits. For locations with recurring blockage problems, mechanical bridge breakers or auxiliary clearing devices may also be considered.
Access openings and clearing devices must allow sufficient working space while maintaining equipment sealing and maintenance safety. Before any cleaning operation, the relevant equipment must be stopped and isolated according to the site procedure. Operators must confirm that there is no remaining hot ash, moving machinery, or hazardous gas exposure before starting work.
Routine Maintenance of Wet Grate Siftings Conveyors
In addition to removing existing deposits, routine maintenance helps maintain reliable conveyor operation.
Checking the Water-Seal Level and Makeup Supply
Inspect the water-seal level, makeup valves, and overflow devices to ensure that the water remains within the designed operating range. A low water level may break the furnace seal, while an excessively high level can affect overflow and normal equipment operation.
Flushing the Water-Seal Trough and Areas Prone to Sediment
Flushing intervals should be determined according to the amount of grate siftings and water quality. Particular attention should be paid to the bottom of the water-seal trough, the discharge outlet, and other areas where sediment tends to accumulate.
The Electric Power Research Institute's Bottom Ash System Maintenance Guide states that sediment in water-seal troughs must be flushed periodically and recommends incorporating the flushing sequence into automatic control. It also emphasizes that flushing flow must be coordinated with drainage capacity and water-seal requirements to prevent loss of the seal. The maintenance recommendations apply to the corresponding bottom ash water-seal systems. The actual flushing interval and flow rate for a wet grate siftings conveyor must be determined according to its own design.
Monitoring Conveyor Operating Conditions
The scraper chain speed, drive motor current, gearbox temperature, and equipment vibration should be checked regularly.
An abnormal increase in motor current, irregular chain movement, or localized ash accumulation may indicate deposits or blockages inside the discharge outlet or conveyor trough. These conditions should be investigated before they lead to equipment failure.
Keeping Spray Nozzles Clear
Inspect the nozzles for blockage and check whether their spray direction remains correct. The flushing water pipes and control valves should also be checked regularly. Filters and pipelines in water supply systems that contain suspended impurities require periodic cleaning.
Custom Machining for Waste Incineration Equipment
Buildup in wet grate siftings conveyors is mainly associated with slurry formation, moisture loss under localized heat, and insufficient removal of accumulated solids. Effective solutions require attention to the actual blockage location, flushing arrangement, water-seal control, and drainage structure. Routine cleaning and equipment monitoring also help prevent deposits from accumulating.
For mechanical components used in waste incineration and environmental protection equipment, we provide custom precision machining based on customer-supplied drawings. Hansheng Automation also manufactures non-standard parts for tobacco packaging machinery and filling machinery, as well as precision components for yacht equipment and radio-controlled racing cars. We support single-piece and small-batch production according to component dimensions, structural details, and assembly requirements.


