A rolling mill flying shear spindle is generally designed as a heavy-duty stepped shaft. It transmits drive torque and supports the shearing components. Its design must account for cutting loads, combined bending and torsional stresses, bearing support, shaft connections, surface strengthening, dynamic balancing, lubrication, and sealing. For large flying shears, the spindle dimensions, material, and heat treatment must be selected according to the machine specifications and operating conditions.
Main Spindle Structure
Shaft configuration and material
The spindle can be manufactured from a 40CrNiMoA alloy steel forging and machined into a stepped shaft. The shaft sections are arranged according to the positions of the bearings, cutter discs, and drive connection. Their diameters, lengths, and transition radii must be determined from the load distribution and available installation space.
Reference data for some large flying shears gives a total spindle length of 2.8 to 6.5 m and a maximum journal diameter of Φ850 mm. The original source cites a 2,800 mm hot strip rolling mill supplied by Zhongnan Heavy Industry as a reference. These dimensions relate to a particular large-scale equipment application and should not be treated as standard dimensions for other flying shear models.
Heat treatment and surface strengthening
The shaft is generally quenched and tempered to a reference hardness of HB270 to HB310. The shearing section may also receive medium-frequency induction surface hardening to improve its resistance to contact loading and surface wear. The reference data specifies a hardened depth of 8 to 12 mm and a surface hardness of HRC52 to HRC55. The actual hardened depth and hardness depend on the shaft diameter, material hardenability, heat treatment process, and operating loads.
Deep rolling can be applied to the cutter-disc mounting section as an additional strengthening process. The reference data gives a rolling force of 12 to 18 kN, with the aim of producing residual compressive stress of approximately 300 to 500 MPa at the surface. The actual result depends on the rolling tool, process settings, material condition, and measurement location. It should be confirmed through process trials or inspection.
Critical Connections and Bearing Arrangement
Cutter-disc connection
A 1:30 tapered fit can be used at the cutter-disc mounting position, with a hydraulic nut providing the axial clamping force. The tapered interface helps locate the cutter disc and transfer loads, while the hydraulic nut applies the required assembly force.
The reference data specifies a preload corresponding to 70% of the shaft material's yield strength. This value should not be adopted as a general assembly requirement. The definition of the preload must first be established, and the design must be checked against the shaft material strength, taper contact pressure, nut capacity, and component dimensions.
Drive-side connection
A cross-type universal joint coupling can be used to connect the spindle to the drive system. The reference data specifies an H7/k6 fit at the shaft connection, with a fit length of at least 1.2 times the shaft diameter.
H7/k6 is a transition fit, not a guaranteed interference fit. Depending on the actual dimensional deviations, the assembled parts may have a small clearance or interference. The fit designation alone does not establish that the connection will always have an interference condition. The torque capacity of the coupling must also be checked against its connection design and the strength of the associated components.
Bearing arrangement
The reference arrangement uses a double-row spherical roller bearing at the drive end, with SKF 231/850 CA given as an example. A four-point contact ball bearing, such as NSK QJ1084N2MA, is listed for the non-drive end.
Double-row spherical roller bearings are suitable for applications with relatively high radial loads and can accommodate a certain degree of misalignment. Four-point contact ball bearings can support axial loads in both directions. Their suitability for the non-drive end must be assessed according to the spindle's axial and radial loads, operating speed, thermal expansion requirements, and locating arrangement. Bearing designations and arrangements should be checked against the manufacturer's current catalogue, actual load calculations, and equipment drawings.
Main Spindle Design Parameters
Dynamic balancing
The reference data specifies a balance quality grade of G2.5. The applicable balancing standard should be selected according to the rotor's dynamic behaviour. ISO 21940-11:2016, including its amendment, applies to rotors with rigid behaviour. Flexible rotors require consideration of ISO 21940-12.
G2.5 is a balance quality grade. It does not represent a fixed permissible residual specific unbalance of 2.5 g·mm/kg. The permissible residual unbalance must be calculated using the rotor mass and operating speed, then allocated to the relevant correction planes.
Torque and deformation limits
The reference data specifies a maximum design torque of 280% of rated torque and gives the following deformation limits:
Maximum deflection under operating conditions: 0.15 mm/m.
Torsional angular deformation: less than 0.25°/m.
These figures should be treated as design inputs or verification targets for a specific machine, not as universal requirements for all flying shear spindles. The actual design torque and deformation limits must account for cutting impact, drive system characteristics, bearing span, material strength, and fatigue loading. ASTM A989, cited in the original material, does not cover torque design for flying shear spindles and should not be used as the basis for these torque requirements.
Sealing and Lubrication
Bearing and shaft sealing
A combination of labyrinth and lip seals can be used to reduce the entry of dust, mill scale, and other contaminants into the bearing and lubrication areas. The reference data gives a temperature range of -20°C to 200°C for the sealing system. The actual operating range depends on the lip seal material, lubricant, shaft surface condition, and seal design. The manufacturer's technical data should be checked when selecting the seals.
Centralized lubrication system
A centralized forced lubrication system can be used for oil-lubricated spindle bearings. The reference data gives the following lubrication parameters:
Lubricant viscosity grade: ISO VG 220.
Oil supply pressure: 0.25 to 0.4 MPa.
Flow monitoring accuracy: ±5%.
These values should be determined according to the bearing type, operating speed, temperature, and resistance of the lubrication circuit. The system must deliver the required oil flow to each lubrication point and monitor oil temperature, pressure, and supply conditions.
Assembly and Heating Precautions
When components with tapered or interference fits require hot assembly, the heating procedure must be selected according to the fit dimensions, material properties, and component geometry. Where heating is required for bearing or component installation, temperature-controlled induction heating can provide controlled and more uniform heating. Direct flame heating should not be used on bearings.
The original material specifies a maximum assembly heating temperature of 180°C. This should not be treated as a universal limit for all bearings, sleeves, and coupling components. Different components have different heat treatment conditions, seal materials, and grease temperature limits. The installation instructions supplied by the component manufacturer should take precedence. Sealed bearings, in particular, may require a much lower heating temperature.
Custom Machining of Flying Shear Spindles and Related Components
Flying shear spindle assemblies may include stepped shafts, sleeves, flanges, coupling components, and other non-standard mechanical parts. Hansheng Automation provides custom precision machining of mechanical components based on customer drawings and technical requirements, with support for single-piece and small-batch orders. For large spindle bodies, the available machining dimensions, raw material condition, heat treatment, and inspection requirements must be assessed against the drawings and actual production conditions.
In addition to components for rolling mill equipment, we also undertake drawing-based machining projects for yacht structural components, RC racing car parts, tobacco packaging machinery, and filling equipment. Machining methods can be assessed according to the geometry and process requirements of each part.


