How to Troubleshoot a Film Winding Machine

Nov 18, 2026 Leave a message

Karen Wong
Karen Wong
As a project manager, Karen oversees the entire lifecycle of projects from planning to execution. Her role ensures timely delivery of high-quality products to meet customer expectations.

 

Troubleshooting a film winding machine involves checking its mechanical drive, electrical components, control system, and pneumatic system. Before starting, identify the machine's symptoms, alarm messages, and operating conditions when the fault occurred. Begin with the components that are easiest to inspect, then narrow down the possible causes step by step. Since winding machines vary in mechanical design and control configuration, inspection methods and operating parameters should follow the equipment manufacturer's technical documentation.

Mechanical system troubleshooting

Worn mechanical components, loose connections, roller misalignment, and faults in the winding mechanism can all affect machine operation. Mechanical inspection should focus on the transmission system, winding assembly, and film transport path.

Inspecting transmission components

First, check the gearbox, motor couplings, chains, and drive belts for looseness, wear, breakage, or abnormal vibration. Periodic noise during operation may indicate damaged bearings, abnormal gear meshing, or incorrect installation of transmission components.

Check the connections between drive shafts and confirm that the bearings rotate smoothly without excessive heat, binding, or radial play. For chain-driven and belt-driven systems, inspect the tension and running alignment. Excessive slack or misalignment can affect power transmission.

Inspecting the winding mechanism

Check the winding shaft, air shaft, and winding core to confirm that the core is not deformed and that the clamping mechanism holds it securely. An improperly secured core or excessive radial runout of the winding shaft may cause winding misalignment, loose rolls, or uneven roll edges.

For machines equipped with pressure rollers, inspect the roller surfaces for wear, aging, and accumulated film residue. Also check whether the pressure roller maintains even contact with the winding roll or driven roller, depending on the machine design.

Roller pressure should be adjusted according to film material, thickness, roll diameter, and machine configuration. Insufficient pressure may cause film slippage or unstable winding, while excessive pressure can leave marks or deform the film. A single fixed air pressure should not be treated as a universal setting for all film winding machines.

Inspecting guide rollers and the film path

Check the installation positions and parallelism of the guide rollers. Inspect their surfaces for scratches, adhesive residue, foreign matter, and localized wear.

Misaligned guide rollers or excessive radial runout can cause web tracking problems, wrinkles, and uneven tension distribution during operation. Also check whether the film follows the specified threading path through each roller assembly. Incorrect threading or improperly positioned guide components may introduce unwanted forces into the film.

Parallelism and runout tolerances should be checked against the machine assembly drawings and manufacturer's specifications. The same tolerance should not be applied indiscriminately to machines with different structures.

Electrical system diagnostics

Electrical faults in film winding machines commonly involve power supply circuits, sensors, motors, and drives. When the machine fails to start, stops unexpectedly, or produces repeated motor alarms, troubleshooting should be based on the electrical schematics and alarm information displayed by the control system.

Checking sensors and detection devices

Inspect photoelectric sensors, proximity switches, limit switches, and web guiding sensors. Check their power supply, wiring, and output signals.

Dust, oil, and film residue on sensor surfaces can interfere with detection. Clean the detection area first, then check the sensor mounting position and confirm that the target is within its effective detection range.

For photoelectric sensors and proximity switches, the detection distance should be adjusted according to the operating principle and manufacturer's specifications. Different sensor models have different rated detection distances, so a single fixed clearance should not be applied to all of them.

When necessary, use a multimeter to check the supply voltage and output signals. The corresponding PLC input status can then be checked to determine whether the signal is being received correctly.

Inspecting motors and servo drives

Check the main drive motor, servo motors, and associated drives. Pay particular attention to power cables, encoder cables, connectors, and terminal connections for looseness or damage.

When a servo drive displays an alarm, record the alarm code and consult the manual for the specific drive model. Common faults include overcurrent, overvoltage, motor overload, encoder feedback errors, and excessive drive temperature.

For example, on some HIWIN D2T-LM series servo drives, E01 indicates a motor short circuit or detected overcurrent. Alarm codes vary between manufacturers and drive models, so the interpretation for one drive should not be applied directly to another.

If motor insulation resistance needs to be measured, first check the manufacturer's specified test method, test voltage, and acceptance criteria. The motor must be disconnected from the servo drive before testing under the prescribed conditions. Some servo motor manuals specify a 500 V insulation test and a minimum insulation resistance of 5 MΩ, but this is not a universal requirement for all servo motors. Never perform an insulation resistance test directly on a servo drive without confirming the manufacturer's procedure, as this may damage its electronic components.

Inspecting wiring and power supply

Check the main power supply, circuit breakers, fuses, control power supply, and terminal connections. Look for unstable voltage, loose connections, damaged cables, and poor electrical contact.

For film winding machines using a 24 V DC control supply, verify that the output voltage meets the rated input requirements of the PLC, sensors, and other control components. Also inspect the wiring of limit switches, safety door switches, and emergency stop circuits to confirm that safety signals are transmitted correctly.

If the machine stops intermittently or loses signals during operation, inspect cable joints, terminal blocks, and electrical connectors for intermittent contact problems caused by vibration or loose connections.

Control system and pneumatic system troubleshooting

When no obvious mechanical or electrical faults are found, but the machine still experiences unstable tension, incorrect roll diameter calculations, speed fluctuations, or incomplete actuator movements, further checks should focus on the PLC, HMI, servo parameters, and pneumatic circuits.

Checking PLC settings and operating parameters

Use the HMI to monitor alarm messages, PLC input and output states, and machine operating parameters. Confirm that the control commands correspond to the actual movements of the actuators.

For automatic winding machines, check the roll diameter calculation, tension control settings, acceleration and deceleration times, and speed coordination between the drive axes.

Taper tension settings should be configured according to the film material, winding method, core diameter, and target finished roll diameter. Incorrect settings may cause excessive tightness at the inner layers, loose outer layers, unstable winding, or uneven roll edges.

During troubleshooting, compare the current settings with the original machine parameters and validated production recipes. Do not apply a fixed tension taper coefficient to machines with different materials and winding requirements.

Checking encoder feedback signals

Encoders are commonly used to measure motor speed, rotational position, or material movement. Their feedback signals directly affect speed regulation and roll diameter calculations.

Check the mechanical connection between the encoder and motor. Confirm that the coupling is secure and that the encoder cable and connectors are undamaged. Use the monitoring interface of the servo drive or PLC to check feedback pulses, actual rotational speed, and position data. Look for missing signals, sudden changes, or incorrect feedback direction.

Encoder resolution, pulse count, and signal format vary by model. Refer to the encoder nameplate and technical documentation for the correct specifications. If feedback data is abnormal, also inspect cable shielding, grounding, and possible electromagnetic interference.

Inspecting the pneumatic system

For film winding machines that use pneumatic cylinders to control pressure rollers, clamping mechanisms, or other actuators, check the air supply pressure, filter regulator, solenoid valves, and pneumatic connections.

If a cylinder moves slowly, fails to reach its required position, or provides insufficient roller pressure, check the air supply, filter condition, pressure regulator, and pneumatic lines for leakage.

Also inspect the solenoid valve operation and cylinder position feedback. Confirm that the piston rod extends and retracts normally and that the associated mechanical mechanism does not bind.

Cylinder stroke and positioning deviations should be assessed according to the cylinder specifications, mounting arrangement, and limit detection method. Allowable deviations must follow the equipment design requirements.

Emergency response and safety precautions

Film winding machines contain high-speed rotating rollers, winding shafts, transmission components, and cutting mechanisms. When an abnormal condition occurs, operators should stop the machine before carrying out further inspections.

Emergency stopping: If the machine develops abnormal vibration, severe noise, film entanglement, or another potentially dangerous condition, press the emergency stop button to stop hazardous movement immediately. Before maintenance, isolate the relevant energy sources using the machine's main disconnect and prevent unexpected restart. An emergency stop button does not replace the energy isolation required for maintenance.

Handling hot components: For brakes, friction pads, and other components that become hot during operation, allow them to cool to a safe temperature before inspection or removal.

Servicing the cutting mechanism: When working on slitting knives or the knife holder, follow the equipment manufacturer's safety procedure and secure the knife holder with an approved locking device to prevent movement or accidental lowering.

Electrical maintenance: Servo drives and inverters may retain hazardous voltage in their internal capacitors after power has been disconnected. Maintenance personnel must follow the discharge time specified in the equipment manual and verify that residual voltage has been eliminated before proceeding.

Post-maintenance inspection: After repairs, remove tools and foreign objects, restore all protective guards, and verify that safety interlocks and emergency stop functions work correctly before conducting a test run.

Maintenance involving electrical, mechanical, and pneumatic energy sources should be performed by qualified personnel in accordance with the equipment manufacturer's maintenance procedures.

Custom machining of precision components for film winding machines

The operating stability of a film winding machine depends not only on its electrical and control systems but also on the machining quality of mechanical components such as winding shafts, guide roller shafts, transmission shafts, and mounting structures.

For non-standard replacement components, Hansheng Automation provides custom machining based on customer-supplied drawings and manufacturing requirements. We support both single-piece and small-batch precision component production.

Our drawing-based machining services also cover components for other industrial equipment, including tobacco packaging machinery and filling machinery, as well as precision yacht parts and structural components for radio-controlled racing cars. Manufacturing processes are evaluated according to the drawings and specific machining requirements of each component.

Mining--Metallurgical-Machinery