A mechanical bar screen removes larger suspended solids, floating matter, and other debris from wastewater before it reaches downstream treatment equipment. Routine maintenance covers operational checks, screenings removal, drive inspection, lubrication, and electrical system checks. The exact tasks and intervals depend on the screen design, operating conditions, and the manufacturer's maintenance instructions.
Checks before and during operation
Before starting the equipment, inspect the frame, screen bars, rake teeth, scraper, and connecting parts. Check for visible deformation, cracks, or loose fasteners. On chain-driven models, look for excessive slack, wear, or misalignment. Inspect the gearbox, bearings, and drive components for oil leaks or seepage, and make sure all guards are securely installed.
After startup, observe the movement of the rake teeth, scraper, or other cleaning components. They should follow their intended travel path without jamming, excessive friction, abnormal vibration, or unusual noise. Pay attention to the motor and gear reducer, and check the control panel for fault indications.
Stop the equipment for inspection if the rake teeth interfere with the screen bars, the chain runs abnormally, or the machine fails to discharge screenings properly. Continuing to operate under these conditions may cause further damage.
Cleaning the screen and surrounding area
The screen collects debris as wastewater passes through it. If the screenings are not removed regularly, they can block the openings, increase flow resistance, and reduce cleaning performance. Remove accumulated debris from the screen surface, discharge chute, and collection hopper according to the incoming solids load and operating conditions.
Check the bottom of the screen and other areas where sludge or fibrous material may accumulate. Fibers wrapped around shafts, chains, or rake teeth should be removed only after the equipment has been stopped and its energy sources have been isolated. Use suitable tools to avoid bending the screen bars, rake teeth, or scraper.
Keep the exterior of the machine and the surrounding area clean. Accumulated waste should not obstruct maintenance access or interfere with equipment operation.
Inspecting and lubricating the drive components
The drive system requires regular attention. On chain-driven screens, check chain tension, wear, and engagement with the sprockets. Adjust or replace the chain according to the manufacturer's instructions if it shows excessive elongation, misalignment, or abnormal wear. Rake attachment links, drive shafts, bearings, and connecting parts should also be inspected.
Check the gearbox oil level, oil condition, and seals at the specified intervals. Correct any low oil level, deteriorated lubricant, or leakage. Apply the lubricant specified by the manufacturer to bearings and other designated lubrication points.
Adding lubricant before every daily startup is not a universal requirement for all mechanical bar screens. Lubrication points and service intervals vary with the machine design. Follow the equipment manual and actual operating conditions to set a lubrication schedule. Both insufficient lubrication and excessive grease application can cause problems.
Checking the electrical system and controls
Inspect the motor, control panel, and accessible cables for abnormal heating, unusual odors, visible damage, or loose connections. During operation, monitor the current, voltage, and fault indicators on the control panel.
For screens equipped with differential level control, timer control, limit switches, or automatic start and stop functions, check the relevant sensors, switches, and protective devices according to the maintenance schedule. These components must respond correctly during startup, shutdown, and fault conditions.
Inspection inside the control cabinet, wiring repairs, and electrical component replacement should be handled by qualified personnel in accordance with site safety procedures.
Maintaining the equipment during extended shutdowns
Before a mechanical bar screen is taken out of service for an extended period, remove screenings and sludge from the screen, rake teeth, discharge chute, and accessible internal areas. Inspect the drive components, bearings, and lubrication system. Apply suitable cleaning, corrosion protection, and protective measures to parts that may be exposed to wastewater or corrosive conditions, as specified in the equipment manual.
During the shutdown period, check the equipment at the intervals recommended by the manufacturer. Where permitted, run the machine periodically to confirm that the motor, gearbox, and drive mechanism move freely without sticking or abnormal noise.
Before returning the screen to service, check the fasteners, lubrication, guards, protective devices, and control functions. Confirm that the equipment is ready for safe operation before restarting it.
Keeping maintenance records
Maintain an operating and service log for each mechanical bar screen. Record operating conditions, unusual noise or vibration, screenings removal, lubrication work, component replacement, and corrective maintenance. These records help identify developing problems such as chain wear, bent rake teeth, bearing deterioration, and gearbox leakage, and provide a basis for maintenance planning.
Hansheng Automation provides custom machining of non-standard mechanical components for mechanical bar screens and other wastewater treatment equipment based on customer drawings. We support both one-off and small-batch orders, as well as precision-machined parts for packaging equipment, textile machinery, and marine applications.


