UV photocatalytic waste gas treatment equipment uses ultraviolet radiation, ozone, and photocatalytic reactions to break down certain organic and inorganic pollutants in industrial exhaust gas. Depending on the equipment design, the treatment process may involve direct photolysis, ozone oxidation, and photocatalytic oxidation.
Under suitable conditions, these processes convert some odor-causing compounds and volatile organic compounds (VOCs) into smaller molecules and oxidation products. Complete oxidation of organic compounds can produce carbon dioxide and water, but the actual reaction products depend on the pollutant composition and operating conditions.
The following sections explain the main reaction mechanisms, the role of the catalyst, and the operating process of this equipment.
Role of High-Energy UV Radiation and Ozone
Ozone Generation from Oxygen Molecules
Some UV oxidation systems use ozone-producing ultraviolet lamps to generate ozone inside the reaction chamber.
When UV radiation at approximately 185 nm strikes oxygen molecules, it can split them into individual oxygen atoms. These oxygen atoms then react with other oxygen molecules to form ozone (O3).
The main reactions are:
O2 + hν (185 nm) → 2O
O + O2 + M → O3 + M
Here, M represents a third body that carries away excess energy during ozone formation.
The amount of ozone generated depends on the lamp output, gas composition, airflow, and contact time. Not all UV lamps produce ozone. The lamp design and quartz envelope determine whether the 185 nm radiation can pass through the lamp material.
Oxidation by Ozone
Ozone is a strong oxidizing agent that reacts with certain organic compounds and odor-causing substances in industrial exhaust.
During treatment, ozone attacks susceptible chemical bonds and initiates oxidation reactions. Depending on the pollutant, this process can break down complex molecules into smaller compounds and further oxidation products.
Ozone can also be decomposed by UV radiation, producing reactive oxygen species that participate in subsequent oxidation reactions.
However, ozone does not react with every pollutant at the same rate. Treatment performance depends on pollutant type, concentration, ozone dosage, temperature, and reaction time.
Combined Effects of UV Radiation and Ozone
Photolysis of Pollutant Molecules
High-energy UV radiation can directly break chemical bonds in certain gas-phase pollutants. This process is known as photolysis.
The equipment directs UV radiation through the exhaust stream inside a reaction chamber. Depending on the radiation wavelength and pollutant absorption characteristics, some molecules absorb photon energy and undergo chemical decomposition.
Pollutants that may be treated by UV photolysis and associated oxidation processes include ammonia, trimethylamine, hydrogen sulfide, methanethiol, methyl sulfide, butyl acetate, ethyl acetate, dimethyl disulfide, carbon disulfide, and styrene.
The actual degradation efficiency varies considerably between compounds. Pollutants that absorb the available UV wavelengths more readily may undergo direct photolysis, while others rely more heavily on reactions with ozone and other reactive species.
Oxidation and Degradation Products
After photolysis or oxidation begins, the resulting intermediate compounds can undergo further reactions with ozone, oxygen radicals, and other reactive species.
For organic pollutants, complete oxidation can convert the carbon and hydrogen components primarily into carbon dioxide and water.
However, complete mineralization does not occur automatically. Some compounds may form aldehydes, organic acids, or other partially oxidized intermediates before further treatment. Inorganic pollutants such as ammonia and hydrogen sulfide also produce reaction products that differ from those formed by organic compounds.
The reaction chamber must therefore provide suitable UV intensity and gas residence time. Additional adsorption, scrubbing, or other post-treatment stages may be required to control residual ozone and reaction by-products.
Role of the Photocatalyst
Catalyst Materials and Structure
Some UV photocatalytic exhaust treatment systems contain a catalyst installed inside the reaction chamber. Titanium dioxide (TiO2) is a commonly studied photocatalytic material.
The catalyst is generally supported on a substrate, which may take the form of a honeycomb structure or metal mesh. This arrangement provides a large contact area between the catalyst, UV radiation, and exhaust gas.
The catalyst material and support structure should be selected according to the pollutant composition, operating temperature, and reactor design. Different photocatalysts have different light absorption characteristics and activation requirements.
Photocatalytic Reaction Mechanism
When suitable UV radiation reaches a semiconductor photocatalyst such as TiO2, it excites electrons from the valence band to the conduction band, leaving positively charged holes behind.
The electrons and holes participate in surface reactions with oxygen and water vapor. These reactions can generate reactive oxygen species, including hydroxyl radicals (OH·) and superoxide radicals (O2·−).
These reactive species attack organic pollutant molecules adsorbed on or near the catalyst surface, promoting their oxidation and decomposition.
The effectiveness of photocatalytic oxidation depends on several factors, including UV wavelength, light intensity, catalyst composition, pollutant concentration, humidity, and gas residence time.
The catalyst does not simply amplify the light source. Its function is to promote chemical reactions by generating reactive charge carriers under suitable irradiation conditions.
Overall Operating Process
Exhaust Gas Intake
Industrial exhaust gas enters the UV photocatalytic treatment unit through an inlet duct, usually with the assistance of an exhaust fan.
Depending on the exhaust composition, pretreatment may be needed to remove dust, paint mist, oil droplets, or other contaminants that could block the reactor or reduce catalyst activity.
UV Irradiation and Oxidation
The exhaust passes through the reaction chamber, where UV lamps irradiate the gas stream.
In ozone-producing systems, UV radiation at approximately 185 nm generates ozone by photodissociating oxygen molecules. The ozone participates in oxidation reactions with suitable pollutants.
At the same time, UV radiation can directly photolyze certain gas molecules. Where a photocatalyst is installed, additional oxidation reactions take place on the catalyst surface.
These processes work together to reduce the concentration of selected organic compounds and odor-causing pollutants.
Exhaust Discharge
After passing through the reaction chamber, the treated gas moves toward the outlet duct.
Depending on the process design, an additional activated carbon filter or other post-treatment unit may be installed to remove residual ozone and reaction intermediates.
The treated exhaust is discharged only after the treatment system meets the applicable emission requirements. Outlet monitoring may be required to verify VOC concentrations, odor levels, and residual ozone.
Main Features and Operating Considerations
Compact Equipment Structure
UV photocatalytic equipment generally uses a modular reaction chamber containing UV lamps and, where applicable, catalyst assemblies. Its relatively compact structure can make installation easier where available floor space is limited.
Treatment of Multiple Pollutants
UV photooxidation can be applied to certain VOCs and odor-causing compounds, including sulfur-containing substances, amines, and selected ester compounds.
However, the treatment response varies with the molecular structure and concentration of each pollutant. The system should be selected according to the actual exhaust composition rather than assuming that one configuration can treat every type of industrial waste gas.
Operating and Maintenance Requirements
The equipment does not require the high combustion temperatures used in thermal oxidation systems. However, UV lamps consume electricity and require periodic inspection and replacement.
The reaction chamber should be kept clean because dust, oil deposits, and other contaminants can block UV radiation or cover the catalyst surface. The catalyst also requires inspection for contamination and loss of activity.
Gas temperature, humidity, airflow, and residence time should be monitored because these conditions directly affect the oxidation process.
Control of Secondary Pollutants
UV and ozone oxidation do not guarantee that all pollutants are completely mineralized. Depending on the exhaust composition and reaction conditions, incomplete oxidation products and residual ozone may remain in the treated gas.
A downstream activated carbon filter, catalytic ozone decomposition unit, or other suitable treatment stage may therefore be required.
The overall process should be tested with representative exhaust gas to confirm its removal performance and identify any secondary pollutants before the equipment is put into service.
Custom Machining for Industrial Equipment Components
In addition to components used in environmental protection and waste gas treatment equipment, Hansheng Automation provides drawing-based precision machining for non-standard industrial parts. Our machining services also cover components for yacht equipment, remote-controlled racing cars, tobacco and packaging machinery, and filling equipment.
We support single-piece and small-batch manufacturing according to customer drawings and component specifications, providing precision machining services for different industrial applications.


