Common Problems with Winding Machines in Practical Applications

Nov 18, 2026 Leave a message

Daniel Tan
Daniel Tan
Head of product marketing, Daniel is responsible for positioning Hansheng's products in the global market. His work includes developing marketing strategies and communicating our value proposition to customers worldwide.

 

Winding machines handle the winding and finishing of continuous materials such as film, nonwoven fabric, paper, and other web materials. During operation, their performance can be affected by the working environment, mechanical installation accuracy, tension control, component wear, and electrical system condition. These factors may lead to unstable operation, difficult roll changes, reduced winding quality, or unplanned downtime. The causes should be assessed according to the machine structure and actual operating conditions rather than attributed to a single component.

Effects of the operating environment on machine performance

Winding machines require a suitable working environment, but not all models need to operate in dust-free conditions. In textile, nonwoven, and film production workshops, dust, fiber debris, oil, and other process residues can accumulate around rollers, bearing housings, and transmission components.

Without regular cleaning and maintenance, oil and fiber debris may enter bearings and moving components, affecting lubrication and normal operation. Fibers can also become entangled around shafts, rollers, and clamping mechanisms, increasing mechanical resistance.

Dust and oil deposited on electrical components, terminals, and cable surfaces may also affect electrical connections and insulation performance. For winding shafts equipped with pneumatic expanding or mechanical clamping mechanisms, accumulated debris and wear may interfere with the expansion and contraction mechanism.

Winding machines therefore require cleaning and maintenance schedules suited to their operating environment. Bearings, guide rollers, transmission components, and winding clamping assemblies should receive particular attention.

Difficulties in installing and removing winding sleeves

Some winding machines use screw-fastened winding sleeves that require operators to tighten or loosen several threaded fasteners during installation and removal. This arrangement can make roll changes time-consuming and may result in inconsistent tightening.

If the threaded fasteners have different insertion depths or tightening forces, the sleeve may not clamp evenly. This can cause positional deviation or increased radial runout, affecting concentricity between the winding shaft and core. During operation, the machine may develop excessive vibration, uneven roll edges, or localized mechanical loading.

Repeated installation and removal can also wear the threads, loosen connections, and damage locating surfaces, increasing maintenance requirements.

For these problems, the locating surfaces, clamping mechanism, mating dimensions, and fastening condition should be inspected. For production lines requiring frequent roll changes, pneumatic expanding shafts, hydraulic clamping mechanisms, or other quick-release structures may be considered according to the machine design.

Unstable winding tension

Tension control directly affects web transport and finished roll quality. Excessive tension can stretch film or fabric and may even cause web breaks. Insufficient tension can produce loose rolls, interlayer slippage, and uneven roll edges.

Common causes of tension problems include:

Faulty tension measurement: Zero drift, incorrect installation, or abnormal signals from tension sensors can prevent the control system from detecting actual web tension accurately.

Unstable drive response: Abnormal operation of the motor, VFD, or servo drive may cause fluctuations in winding speed and output torque.

Incorrect control settings: Poorly matched tension setpoints, taper tension compensation, acceleration and deceleration settings, or roll diameter calculations can cause tension variations during winding.

Changes in material properties: Variations in film thickness, paper basis weight, moisture content, and cross-web properties can also contribute to uneven tension distribution.

Winding quality depends on more than tension. Nip pressure, winding torque, roller parallelism, core condition, and material uniformity also affect roll formation. Simply increasing or decreasing the tension will not correct every winding defect.

Electrical control system failures

Winding machines typically use PLCs, sensors, VFDs, or servo drives to coordinate motors, tension measurement, and automatic roll changeover mechanisms. A fault in any of these components can affect machine operation.

Common electrical problems include:

Wiring faults: Damaged cables, loose terminals, or poor electrical connections may interrupt signals and cause intermittent machine stoppages.

Sensor failures: Faults in photoelectric switches, proximity switches, encoders, or tension sensors may cause incorrect position detection, speed feedback, or tension measurement.

Drive alarms: Overcurrent, overvoltage, overload, and overtemperature alarms from VFDs or servo drives may trigger protective shutdowns.

Control program errors: Incorrect PLC parameters, interlock conditions, or operating sequence settings may cause abnormal actuator movements or prevent the machine from following the programmed sequence.

Troubleshooting should be based on alarm codes, PLC input and output states, and drive monitoring data. Electrical components should not be replaced without first identifying the fault.

Wear of mechanical transmission components

Bearings, gears, chains, drive belts, and couplings are exposed to loads, friction, and vibration during prolonged operation.

Insufficient bearing lubrication, poor installation alignment, or excessive loads can lead to wear, abnormal heating, and operating noise. Drive belts and chains may stretch, loosen, or break due to fatigue, incorrect tension, or prolonged use.

Winding shafts, guide roller shafts, and expanding clamping components can also wear under frequent starts and stops and repeated roll loading and unloading. This may affect rotational accuracy and component fit.

Mechanical wear increases maintenance costs and may cause roller vibration, reduced transmission efficiency, and web tracking problems. Regular inspections should therefore cover bearing clearance, gear meshing, belt tension, and wear on shafts and other mechanical parts.

Motor overheating and machine overload

During prolonged operation or frequent acceleration and deceleration, the motors, drives, and transmission components of a winding machine may experience elevated temperatures and excessive loads.

Common causes include:

Excessive mechanical load: Rolls that exceed the machine's design capacity or transmission components that are binding can increase motor load.

Incorrect operating parameters: Unsuitable motor power, reduction ratio, acceleration time, or braking settings may cause frequent overloads or abnormal current levels.

Insufficient cooling: Motor fan failure, blocked ventilation passages, or high ambient temperatures can reduce the cooling performance of motors and drives.

Increased mechanical friction: Damaged bearings, abnormal gear meshing, or transmission misalignment can increase running resistance and motor load.

When motor or drive temperatures exceed their permitted limits, the protection system may generate an alarm or stop the machine. Prolonged operation under overload conditions can damage motor windings, drive power components, and other associated parts.

When overheating or overload alarms occur, check the actual load, current, cooling conditions, and mechanical transmission system. Do not raise protection thresholds or disable overload protection simply to keep production running.

Inconsistent winding quality

Winding quality is an important indicator of machine performance. Changes in material properties, tension, nip pressure, or mechanical alignment may cause uneven roll edges, inconsistent winding hardness, wrinkles, and roll diameter deviations.

Common winding defects and their contributing factors include:

Web wrinkles: These may result from uneven tension distribution, misaligned guide rollers, cross-web thickness variations, or poor nip contact.

Loose rolls: Common causes include insufficient winding tension, inadequate core clamping, and an unsuitable winding torque setting.

Interlayer slippage and uneven roll edges: These can result from a combination of winding tension, nip pressure, material surface friction, and core installation conditions.

Starring or roll collapse: Uneven internal stress and variations in pressure between wound layers can cause localized collapse near the core.

Roll diameter calculation errors: Incorrect encoder feedback, material thickness settings, or diameter calculation programs can cause discrepancies between the displayed and actual roll diameter, affecting length-controlled winding, automatic roll changes, and packaging arrangements.

Roll weight and roll diameter are two different measurement parameters. Roll diameter can be estimated or measured using suitable sensors and control algorithms. When accurate roll weight records are also required, a weighing device or another suitable measurement system is necessary. Roll weight cannot be determined accurately from roll diameter alone.

Winding defects usually result from a combination of machine condition, material properties, and process settings. Troubleshooting should therefore include checks of web tension, nip load, roller alignment, core condition, and cross-web material uniformity rather than focusing on a single control parameter.

Custom machining of precision components for winding machines

The long-term operating condition of a winding machine depends partly on the machining quality and assembly accuracy of components such as winding shafts, guide roller shafts, transmission shafts, expanding clamping mechanisms, and bearing housings.

For non-standard replacement parts or components required for machine modifications, Hansheng Automation provides custom machining based on customer-supplied drawings and manufacturing requirements. We support both single-piece and small-batch precision component production.

Our drawing-based machining services also cover components for industrial equipment such as tobacco packaging and filling machinery, as well as precision structural parts for yachts and radio-controlled racing cars. Manufacturing processes are evaluated according to the drawings and specific machining requirements of each component.

Mining--Metallurgical-Machinery