When a plate-and-frame filter press is operating, filter plates may develop cracks, become damaged, or break completely. This type of failure is commonly referred to as filter plate breakage. It can interrupt filtration, cause slurry leakage, damage the equipment, and create safety risks.
Common causes include abnormal feed pressure, uneven chamber filling, blocked feed channels, incorrect plate arrangement, changes in material properties, and structural damage to the equipment. One of the main factors to investigate is pressure imbalance across the filter plates. When adjacent chambers have significantly different pressure and cake formation conditions, the plates may be subjected to differential loads beyond their normal design limits.
Troubleshooting should therefore cover more than the damaged plates themselves. The feed system, plate arrangement, filtration conditions, and frame structure must also be inspected to identify the cause of abnormal loading.
Common Causes of Filter Plate Breakage
Incorrect Operating Procedures
Failure to follow the specified operating sequence when starting the feed pump, opening valves, or discharging filter cakes can cause abnormal pressure conditions and uneven chamber filling.
Incorrect valve operation: If the feed valve or filtrate outlet valves remain closed when the feed pump starts, the pump pressure may rise rapidly. High feed velocity or constant-flow pumping can also produce pressure surges during startup or flow adjustments, exposing the plates to abnormal loads.
Incomplete cleaning after cake discharge: If filter cake residue and foreign material remain in the feed ports, feed channels, or drainage areas after discharge, blockages may occur during the next cycle. Some chambers may then receive insufficient feed or experience restricted filtrate flow.
Incorrect filter plate arrangement: When replacing filter plates or frames, failure to follow the specified sequence and orientation may interfere with material distribution. Misalignment between the cloth openings and plate feed ports can also restrict flow and contribute to pressure imbalance.
Intermittent feed pump operation: Frequent pump starts and stops during filtration can allow sludge to settle or create localized blockages in the chambers. Restarting the pump at high pressure may result in uneven feeding and abnormal differential pressure.
Changes in Material Temperature and Filtration Properties
The temperature of the feed material affects its viscosity and filtration behavior. Power outages, equipment failures, or shutdowns during shift changes may cause the liquid temperature to move outside the required process range. This can change the material viscosity and increase resistance in the feed piping and filter chambers.
For liquids whose viscosity increases significantly as they cool, a lower temperature may reduce the feed rate. If the pump continues operating at the original flow or pressure setting, system pressure may rise rapidly.
Excessively high temperatures can also exceed the rated temperature of the filter plate material, resulting in material degradation or plate deformation.
A low temperature does not automatically cause filter plate breakage. The relationship between temperature and viscosity, the temperature rating of the plate material, and the actual filtration conditions must all be considered.
Filter Plate Arrangement and Equipment Design Problems
The plate arrangement and frame structure affect how loads are distributed across the filter chambers.
Incorrect number or arrangement of plates: If the plate count is below the specified quantity, the sequence is incorrect, or the required dummy plates are not installed correctly when reducing the chamber volume, uneven chamber filling and abnormal pressure differences may occur.
Inadequate filter plate design: If the plate material, thickness, or structural strength is insufficient for the specified operating pressure and service conditions, cracks or breakage may develop during prolonged operation or abnormal pressure events.
Insufficient structural support: If the main beams, support members, or frame connections lack adequate stiffness or become deformed, plate alignment and closing conditions may be affected. This can result in uneven plate loading. An uneven foundation or incorrect frame installation should also be checked.
Material Blockage and Excessive Filtration Resistance
Feed materials containing large amounts of colloidal substances, fine particles, or other difficult-to-filter components can accumulate on the filter cloth or block feed and drainage channels.
For example, gel-like substances such as iron-containing colloids may increase filtration resistance and reduce filtrate flow. If the feed pump continues to increase pressure while the liquid cannot drain properly, uneven chamber filling and abnormal differential pressure may develop.
Blocked feed ports, restricted filtrate outlets, and significant differences in filter cloth permeability can also cause adjacent chambers to develop different cake thicknesses and pressure conditions.
Uneven Loading on Filter Plates
Uneven loading is an important factor in filter plate breakage. Particular attention should be paid to differences in feed distribution and filtration conditions between adjacent chambers.
Uneven feed distribution: If the feed channel design is unsuitable, sections of the piping are blocked, or slurry distribution is uneven, some chambers may fill completely while others remain empty or partially filled. This can create an imbalance in pressure across the filter plates.
Differences in filter cloth permeability: Using filter cloths with significantly different permeability within the same plate pack can result in different filtration rates and cake formation patterns between chambers.
Inconsistent chamber thickness: Mixing filter plates or frames with different thicknesses, or installing them in an incorrect sequence, may produce different loading conditions between adjacent chambers.
Excessive feed velocity: If the feed pump flow rate or pressure curve does not match the filtration characteristics of the material, excessive feed velocity or pressure surges may expose the plates to abnormal loads.
Single-side feeding does not automatically cause plate breakage. The risk depends on the design of the plates and feed channels. Equipment requiring multiple feed points or a special distribution arrangement should follow the original manufacturer's design. Feed locations and hydraulic configurations should not be modified without engineering approval.
Solutions to Filter Plate Breakage
Follow the Correct Operating Procedure
Before feeding, inspect the feed valve, filtrate outlet valves, and other relevant valves. Make sure they are in the specified operating positions before starting the feed pump.
Build up the feed flow and pressure gradually according to the operating procedure. Avoid applying high pressure suddenly. If feeding has been interrupted because of a shutdown, check the feed ports for blockages before restarting. Begin at a low pressure and increase it gradually as required by the manufacturer's instructions.
After each cake discharge, clean the feed ports, plate feed channels, and drainage areas to remove residual cake and prevent blockages during the next cycle.
When replacing filter plates or frames, follow the specified plate sequence and orientation. Check that the filter cloth openings align with the corresponding plate ports.
Maintain the Correct Plate Arrangement
Before operation, verify the number, sequence, and orientation of the plates and frames against the equipment nameplate and manufacturer's specifications.
For short batches with insufficient solids to fill all chambers, a purpose-designed dummy plate or spacer arrangement may be used to reduce the effective chamber volume, provided that the equipment design allows it.
Install dummy plates only in the specified positions. Do not use the moving closing plate as a substitute or change the chamber arrangement by simply removing filter plates.
Control Feed Pressure and Flow Rate
The feed pump flow rate and pressure must match the filtration characteristics of the material. For materials that develop high filtration resistance, establish the feed pressure and flow profile through filtration testing and the equipment's rated specifications.
At the beginning of filtration, use an appropriate low-pressure feed condition to allow the chambers to fill progressively and form an even cake layer. Adjust pressure and flow gradually according to the filtration conditions.
If the feed pump starts and stops frequently, inspect the pump selection, control settings, and feed supply conditions to identify the cause. Do not compensate for blocked piping or restricted filtrate discharge by continuously increasing feed pressure.
Improve Material Filtration Conditions
For materials containing iron gel, colloidal particles, or other components that are difficult to filter, suitable pretreatment may be required.
For example, screening can remove larger impurities. Flocculants or filter aids may also be selected through testing to improve filterability and reduce filter cloth blinding and uneven chamber filling.
If the process specifies a temperature range, use appropriate monitoring to keep the feed material within that range. For liquids whose viscosity changes significantly with temperature, adjust the feed flow and pressure according to actual operating conditions.
Inspect the Filter Plates and Frame Structure
If a filter plate develops cracks, deformation, or other structural damage, stop using it and investigate the cause.
Replace broken plates with components that meet the original specifications. Do not continue using damaged plates after simple bonding or heat reshaping unless the manufacturer has approved a repair procedure.
Inspect the main beams, support members, guide rails, and frame connections for deformation. Check that the foundation remains level and that the plate pack is correctly aligned and clamped.
If the equipment has a structural design problem, the manufacturer or qualified technical personnel should assess the plate material, structural strength, and support arrangement. Increasing the closing force or changing the feed arrangement alone will not correct every structural problem.
Maintain Uniform Plate Loading and Feed Distribution
Make sure that each chamber receives slurry and discharges filtrate according to the equipment design. Empty chambers, blocked channels, and incomplete filling should be avoided.
Check filter cloth permeability regularly. Avoid using cloths with significantly different filtration characteristics in the same plate pack.
For presses with special feed arrangements, inspect the feed piping, distribution channels, and connections to confirm that slurry reaches the chambers as intended.
If the filtrate discharge passages are blocked, clean the drainage areas behind the filter cloths and the corresponding outlet ports to restore normal flow.
What Should Be Monitored to Prevent Filter Plate Breakage?
During routine operation, pay attention to the following warning signs:
Uneven filter cake thickness: If adjacent chambers contain cakes of noticeably different thicknesses, or some chambers remain partially empty, inspect the feed ports and filtrate outlets for blockages.
Sudden increase in feed pressure: If feed pressure rises rapidly without a corresponding increase in filtrate flow, inspect the piping, filter cloths, and internal plate channels. Do not continue forcing material into the press.
Cracked or deformed filter plates: Stop using damaged plates and check for pressure imbalance, material degradation, or mechanical problems in the frame structure.
Unstable feed pump operation: Frequent starts and stops, flow fluctuations, or abnormal vibration require investigation before filtration resumes.
Filter plate breakage is rarely caused by a single component alone. It can result from the combined effects of feed conditions, filtration resistance, and uneven loading across the filter chambers. Correct operating procedures, uniform chamber filling, clear feed and drainage channels, and regular inspection of the plates and frame help reduce the risk of plate failure.
In addition to mechanical components used in filter press equipment, Hansheng Automation provides precision machining services for several manufacturing industries. We manufacture custom functional components for filling and tobacco packaging machinery, as well as precision parts for yacht equipment and structural components for remote-control racing cars, according to customer-supplied drawings. Both single-piece and small-batch precision machining are supported.


