A traveling-bridge sludge suction machine is used to collect and remove settled sludge from horizontal-flow sedimentation tanks. The equipment typically has a working bridge spanning the tank, with drive units moving it back and forth along the tank length. During travel, the suction system draws settled sludge from the tank floor and conveys it through discharge pipes to a sludge channel or downstream treatment facility.
According to the sludge removal method, suction machines can be classified as siphon-type, pump-suction, or water-level-difference types. Based on the drive arrangement, they can be classified as center-driven, peripheral-drive, or traveling-bridge types. Traveling-bridge suction machines are mainly used in rectangular horizontal-flow sedimentation tanks, where sludge is collected as the bridge moves along the tank.
Main Components of a Traveling-Bridge Sludge Suction Machine
Working Bridge and Main Support Structure
The working bridge is the main load-bearing component of the traveling-bridge sludge suction machine. It generally uses a steel truss or box-girder structure spanning the width of the sedimentation tank. Both ends are supported by traveling mechanisms running on tracks installed along the tank walls.
The bridge carries the drive units, suction pipes, suction assemblies, electrical equipment, and associated components. Its structural strength and rigidity must be designed according to the tank span, equipment weight, and operating loads.
Carbon steel with protective coatings is commonly used for the bridge. Depending on wastewater corrosiveness and project requirements, stainless steel may also be selected. Material selection and surface treatment should match the actual operating environment.
Drive and Traveling Mechanism
The drive system mainly consists of electric motors, gear reducers, drive wheels, transmission components, and supporting structures. A dual-side drive arrangement is commonly used, with drive units installed at both ends of the working bridge. The traveling wheels move the entire machine along the tracks.
Some designs use shaft-mounted gear reducers, which provide a compact arrangement and simplify installation and maintenance. The two drive units must operate in coordination to prevent bridge skewing, rail climbing, or travel obstruction.
Overload protection and travel limit switches can also be installed. When the operating resistance exceeds the preset limit, the overload protection device can stop the drive. When the bridge reaches either end of the tank, the limit switches send signals to the control system to stop or reverse its movement.
Sludge Suction System
The suction system is the main working assembly of the machine. It generally includes a main suction pipe, branch pipes, suction nozzles, flow control valves, and connecting components. The suction nozzles are arranged beneath the working bridge and maintained at their designated positions by suspension frames or support structures.
As the machine moves, the suction inlets collect sludge from the corresponding areas of the tank floor. The sludge-water mixture enters the suction piping and flows into the discharge system.
The number, spacing, and installation height of the suction nozzles depend on tank dimensions, sludge distribution, and discharge requirements.
Pump-suction machines generally use submersible pumps or other pumps suitable for handling solids-laden fluids to convey sludge outside the tank. Siphon-type machines require a vacuum-assisted device to establish the siphon before sludge can be discharged through the water-level difference between the sedimentation tank and the discharge channel.
The piping arrangement and control system differ between these two methods. Their components should not be treated as a single standard configuration.
Sludge Discharge System
The discharge system conveys the sludge-water mixture collected by the suction pipes to its designated destination. Its main components include discharge headers, sludge channels, discharge pipes, and associated valves.
In systems with multiple suction branches, the collected sludge can be combined through a common header before discharge. Some machines also use flow control valves or electrically operated discharge valves to regulate the flow rate and discharge sequence of individual pipelines.
Pipe diameters and valve specifications must be determined according to sludge flow rate, solid particle characteristics, conveying distance, and pipeline resistance.
Auxiliary Components of a Traveling-Bridge Sludge Suction Machine
Rails and Traveling Wheels
Rails are installed along both sides of the sedimentation tank to guide the working bridge. The traveling wheels run along these rails and support the equipment load. Depending on the design, the wheels may be made of steel or fitted with an elastic polyurethane coating.
Rail installation requires proper control of levelness, parallel alignment, and elevation. Incorrect alignment can cause bridge skewing, rail wear, or unstable travel.
Scraper and Sludge-Guiding Assembly
Some suction machines include scraper blades or V-shaped guide plates near the suction nozzles. These components direct settled sludge toward the inlets and help reduce residual sludge at the bottom of the tank.
They are generally installed beneath the suction suspension frame. Their mounting height and position must be adjusted according to the tank floor structure.
Travel Limit and Collision Protection Devices
Travel limit switches are installed at the designated control positions. When the working bridge reaches either end of the tank, the trigger mechanism activates the limit switch and sends a signal to the control system for deceleration, stopping, or reversing.
Some machines also include mechanical collision guards or buffer devices to reduce the impact between the bridge and the end structures of the tank under abnormal operating conditions.
Electrical Control System
The control cabinet generally includes the main power switch, operating buttons, control components, overload protection, and alarm devices. Some machines use a programmable logic controller (PLC) to control bridge travel cycles, direction changes, and stopping intervals according to process requirements.
Wireless remote control and remote monitoring interfaces can also be included in projects that require remote operation. The actual control functions depend on the equipment configuration and site automation requirements.
Main Technical Specifications
The specifications of a sludge suction machine must be determined according to tank dimensions, sludge characteristics, suction method, and equipment configuration. Section 4.4.3 of HJ/T 266-2006 provides basic parameters for traveling-bridge sludge suction machines and can be used as a reference for equipment design and selection.
| Parameter | Standard requirement or design basis |
|---|---|
| Applicable tank width | The standard lists 4 m, 6 m, 8 m, 10 m, 12 m, 14 m, 16 m, 18 m, 20 m, 22 m, 25 m, and 30 m |
| Drive motor power | Grouped maximum values include 0.37 kW, 2 × 0.37 kW, 2 × 0.55 kW, and 2 × 0.75 kW |
| Sludge pump power | Grouped maximum values include 3.0 kW, 2 × 3.0 kW, 3 × 0.55 kW, and 4 × 3.0 kW |
| Vacuum pump power | Listed maximum values include 1.5 kW and 2.2 kW |
| Traveling speed | 0.6 to 1.2 m/min |
| Suction pipe diameter and nozzle spacing | Determined according to design flow rate, tank dimensions, and suction system layout |
| Tank depth and suction nozzle elevation | Determined according to tank structure, sludge layer thickness, and suction performance |
The power ratings above are grouped upper limits listed in Table 3 of the standard. They are not components that must all be installed on every machine. Actual equipment selection also requires checking the treatment flow rate, sludge concentration, pump head, and discharge pipeline resistance.
Selection and Installation Considerations
The first step in selecting a traveling-bridge sludge suction machine is to confirm the sedimentation tank width, length, depth, and treatment load. The sludge settling characteristics should then be considered when selecting pump-suction, siphon, or water-level-difference discharge.
For pump-suction systems, check the pump flow rate, head, and solids-handling capacity. For siphon systems, verify the available water-level difference, vacuum-assisted equipment, and discharge pipeline conditions.
During installation, check the levelness, parallel alignment, and elevation of the two tracks. These factors affect the stability of the traveling mechanism. The bridge span, suction nozzle elevation, discharge pipe connections, and travel limit positions must also be checked before commissioning.
After installation, carry out no-load and load tests according to the manufacturer's requirements. Verify the operation of the traveling mechanism, suction system, discharge piping, and electrical control system.
Custom Machining of Traveling-Bridge Sludge Suction Machine Components
A traveling-bridge sludge suction machine contains various mechanical components, including bridge connectors, drive shafts, suction pipe supports, suction nozzle mounting brackets, scraper blade connectors, pump supports, and traveling wheel mounting structures. Tank dimensions and equipment layouts vary between projects, so some non-standard components require machining according to the actual design drawings.
We provide single-piece and small-batch precision machining based on customer-supplied drawings. Hansheng Automation supports custom machining of non-standard mechanical components according to their structural, dimensional, and assembly requirements.
Our precision machining services also cover other manufacturing industries. In addition to wastewater treatment equipment parts, we manufacture precision components for tobacco packaging and filling machinery, as well as yacht components and precision structural parts for remote-controlled racing cars.


