How to Select a Plate-and-Frame Filter Press

Nov 20, 2026 Leave a message

David Park
David Park
A control systems engineer with expertise in automation solutions, David works on developing innovative control technologies that enhance the efficiency and precision of our gear reducers.

 

Selecting a plate-and-frame filter press requires several process parameters, including the amount of sludge to be treated, feed solids content, target filter cake moisture content, and daily operating hours. In addition to calculating the daily dry solids load, the selection process must determine the filter cake volume per cycle and use the required chamber volume, filtration area, and actual filtration rate to establish the equipment specifications.

Before selecting a press, obtain the sludge data at the filter press inlet whenever possible. If the wastewater treatment plant only provides the total raw wastewater volume rather than the sludge feed volume, the actual sludge flow rate and solids content after sedimentation, thickening, or other pretreatment must first be determined. The total wastewater flow should not be used directly as the filter press feed volume.

Determine the Basic Parameters for Filter Press Selection

The following information should be collected before selecting the equipment:

Daily feed quantity: Determine the mass, volume, and actual feed flow rate of the sludge or slurry entering the filter press each day.

Feed solids content: This is the proportion of dry solids in the incoming sludge. It directly affects the daily dry solids load.

Target filter cake moisture content: Set this according to the requirements for sludge treatment, transportation, and disposal. A lower moisture content generally means that more water must be removed and may require different filtration conditions.

Daily operating hours: Determine how many hours the equipment can operate each day to calculate the number of filtration cycles required.

Sludge properties: Consider the sludge source, particle characteristics, compressibility, and filterability. These factors affect filter cloth selection, chemical conditioning, and actual filtration speed.

Once these parameters are established, the required equipment capacity can be calculated.

Calculate the Daily Dry Solids Quantity

The daily dry solids quantity is one of the main parameters used in filter press sizing. It represents the mass of solid material in the feed, excluding water.

The calculation is:

Daily dry solids = Daily feed mass × Feed solids content

For example, assume that the sludge or slurry entering the filter press weighs 1,000 tonnes per day and has a feed solids content of 1%.

1,000 × 1% = 10 tonnes

The daily dry solids load is therefore 10 tonnes.

This example assumes that the 1% solids content is expressed as a mass fraction and that all the feed is processed by the filter press. If the actual solids capture rate is below 100%, the result must be adjusted according to the equipment's solids recovery rate. When the feed quantity is given in m³/d, the feed sludge density must also be included in the conversion.

Calculate the Dewatered Sludge Mass Based on Filter Cake Moisture Content

The filter cake discharged from a plate-and-frame filter press still contains some moisture. Therefore, the dry solids quantity alone cannot represent the actual discharge mass.

First, convert the target filter cake moisture content into its dry solids fraction.

Cake dry solids fraction = 1 − Filter cake moisture content

Wet filter cake mass = Daily dry solids ÷ Cake dry solids fraction

For example, assume that the target filter cake moisture content is 75%. The corresponding cake dry solids fraction is 25%.

Using the previously calculated 10 tonnes of dry solids:

10 ÷ (1 − 75%) = 40 tonnes

The daily wet filter cake production is therefore approximately 40 tonnes.

Moisture content and solids content must be distinguished. A filter cake with 75% moisture contains 25% dry solids. The correct result is 40 tonnes, not 17.5 tonnes. The 75% moisture content in this example is an assumed design target. The actual target should be confirmed through sludge filtration tests.

Calculate the Hourly Throughput and Cake Mass per Cycle

After determining the daily wet filter cake mass, divide it by the actual daily operating hours to calculate the required hourly output.

The formula is:

Hourly filter cake production = Daily wet filter cake mass ÷ Daily operating hours

Assuming that the press operates for 8 hours per day:

40 ÷ 8 = 5 tonnes/hour

If each complete filtration cycle takes 4 hours, the equipment can complete two cycles per day.

The formula is:

Filter cake mass per cycle = Hourly filter cake production × Cycle time

5 × 4 = 20 tonnes per cycle

The press must therefore accommodate approximately 20 tonnes of wet filter cake in each cycle.

The 4-hour cycle time should include all operations, such as feeding, filtration, pressing, cake discharge, and necessary cleaning. If 4 hours refers only to the filtration stage, the time required for the other operations must also be included in the production schedule.

Calculate the Required Chamber Volume and Filtration Area

After calculating the filter cake mass per cycle, determine its volume to establish the required chamber capacity.

The formula is:

Filter cake volume = Filter cake mass per cycle ÷ Wet cake bulk density

Assume that the wet filter cake bulk density is 1 tonne/m³:

20 ÷ 1 = 20 m³

The press must therefore accommodate approximately 20 m³ of filter cake per cycle.

Once the cake volume is known, the required filtration area can be estimated from the chamber volume available per unit of filtration area.

The formula is:

Required filtration area = Filter cake volume per cycle ÷ Chamber volume per unit filtration area

Assume that the specific chamber volume is 15 L/m², equivalent to 0.015 m³/m²:

20 ÷ 0.015 ≈ 1,333.33 m²

Under these assumptions, the theoretical filtration area required is approximately 1,333 m².

If the project requires an additional 20% allowance:

1,333.33 × 1.2 ≈ 1,600 m²

This gives an estimated filtration area of approximately 1,600 m².

The value of 15 L/m² is an assumption for this example, not a standard specification for all plate-and-frame filter presses. Wet cake bulk density, chamber utilization, and the design allowance should be established using actual sludge test results and the manufacturer's technical data.

It is also important to distinguish filtration area from chamber volume. Chamber volume determines how much filter cake the press can hold in one cycle, while filtration area affects the filtration rate and the rate at which liquid passes through the filter cloth. Even when the chamber volume is sufficient, the press must still be checked to confirm that it can complete dewatering within the specified cycle time.

Select the Filter Press Model Based on the Calculations

After calculating the sludge load, wet cake mass, chamber volume, and filtration area, the next step is to select a suitable filter press model from the manufacturer's specifications.

The following equipment parameters should also be checked:

Filter plate dimensions and quantity

Determine the filter plate dimensions, quantity, and chamber thickness according to the required filtration area and chamber volume. The plate quantity and arrangement must match the frame design and plate-shifting system.

Filtration pressure

Determine the required feed pressure and pressing pressure based on sludge properties and filtration test results. Check that the filter plates, frame, and sealing structure have sufficient pressure ratings.

Filter plate and filter cloth materials

Select suitable filter plate and filter cloth materials according to the pH, temperature, and chemical composition of the sludge. The selected materials must meet the requirements for filtration and long-term operation.

Automation configuration

Choose a manual, semi-automatic, or fully automatic plate-shifting system according to the production scale and available labor. Automatic cake discharge and filter cloth washing can also be considered where required.

Auxiliary equipment

Select a suitable feed pump according to the feed rate and filtration pressure. The supporting system should also account for sludge conditioning, chemical dosing, filtrate collection, and filter cake conveying.

What Else Should Be Considered When Selecting a Plate-and-Frame Filter Press?

Theoretical calculations help establish the initial equipment specifications, but they cannot fully replace actual sludge filtration tests. Different types of sludge have different particle compositions, compressibility, and filtration resistance. Even when the feed solids content is the same, the filtration rate and final filter cake moisture content may vary considerably.

Before purchasing the equipment, it is advisable to conduct laboratory or pilot-scale filtration tests using the actual sludge. Confirm the filter cake moisture content, solids recovery rate, filtration cycle time, and chemical consumption. Use these results together with the daily processing requirements to determine the final chamber volume and filtration area.

In addition to precision components for filter press equipment, our machining services cover a range of manufacturing industries. Hansheng Automation manufactures custom components according to customer-supplied drawings, including functional parts for tobacco packaging and filling machinery, as well as precision components for yacht equipment and remote-control racing cars. Single-piece and small-batch precision machining are supported.

Environmental-Protection-Machinery