When using film laminating machines and shrink wrapping machines, handle mechanical, electrical, and heat-related risks separately. Cover three stages: before operation, during operation, and fault response.
Common hazards and responses for film laminating machines
1.1 Mechanical pinch and crush risk
Risk: Rotating parts such as feed rollers, cutting blades, and positioning rollers may lack guards. Hands can be pinched when reaching inside. If the workpiece is not fixed during lamination, it can shift and be pulled into the machine.
Response:
Before startup, confirm that the guard mesh and covers are fully installed. Do not remove guards to operate.
During feeding and lamination, keep both hands at least 10 cm from rotating parts. Do not wear gloves at the cutting station.
If material jams, cut main power first. Wait until all parts stop before clearing the jam.
1.2 Electrical leakage risk
Risk: Moisture, damaged cables, or delayed repair can lead to contact with live parts during lamination and cause electric shock.
Response:
Before work each day, use a multimeter to check the equipment grounding resistance. It must be ≤4 Ω.
Do not place water, cleaning agents, or other liquids at the lamination station. If cable damage is found, stop the machine and report it for repair.
Disconnect power before cleaning. Do not wash the machine body with water.
1.3 Cutting blade injury risk
Risk: Manual blade changes without power isolation or proper tools can cause the blade to slip and cut hands.
Response:
Use the insulated wrench supplied with the machine to replace cutting blades. Do not insert or remove blades by hand.
Put idle blades in a dedicated storage box. Do not leave them on the worktable.
Keep the workpiece at a 45° angle to the blade edge during cutting. Avoid hard pushing that can throw the blade and cause cuts.
We can machine feed rollers, guide wheels, blade holders, and guard brackets for film laminating machines from customer drawings, in single pieces or small batches. Hansheng Automation works to drawing dimensions and assembly clearances.
Common hazards and responses for shrink wrapping machines
2.1 High-temperature burn risk
Risk: Heating chambers and shrink rollers can reach over 150°C. Close contact or cleaning before cooldown can cause burns. Hot air outlets aimed at the body can cause scalding.
Response:
Do not open the heating chamber door while the machine is running. After shutdown, wait at least 30 minutes until surface temperature drops below 60°C before cleaning.
Install heat insulation guards at the shrink station. Keep arms at least 30 cm from hot air outlets during operation.
For burns from hot surfaces, rinse with running cold water for at least 15 minutes. Seek medical help if severe.
2.2 Hot air burn and inhalation risk
Risk: Poor hot air circulation during shrink wrapping can cause hot exhaust gas to build up. Without an exhaust filter, toxic gases from heated plastic film may be inhaled.
Response:
Make sure the exhaust filter unit supplied with the machine runs normally. Replace the filter cotton once a week.
Install an exhaust system at the shrink station. Air changes must be at least 15 times per hour.
If abnormal hot air odor appears, stop the machine and check it. Prevent buildup of harmful substances from high-temperature decomposition.
2.3 Film roll entanglement and mechanical injury
Risk: If the shrink film roll is not fixed securely, it can come off and fly out at high speed. If film jams and the operator pulls it without cutting power, fingers can be pulled in.
Response:
Use the dedicated lock to fix the shaft end when installing the film roll. Confirm it is locked before startup.
If film jams, cut power first. Use a proper tool to slowly remove the jammed film. Do not pull it by hand.
Do not approach the film roll discharge end while the machine is running. This prevents flying film or parts from causing injury.
General emergency response
Post a map of emergency stop button locations on all equipment. Press the main stop button first in an emergency.
Equip the workshop with insulated gloves, insulating mats, fire blankets, and other emergency supplies. Place them within 1 meter of the equipment.
Carry out a weekly equipment safety inspection. Focus on guards, cables, and the temperature control system.
Our precision parts machining service is not limited to film laminating and shrink wrapping machines. Hansheng Automation can machine custom parts from drawings for food packaging equipment, filling machinery, tobacco packaging machinery, and printing machinery. We also cover yacht fittings, RC car structural parts, and medical device parts. Single pieces and small batches are both available, with attention to material, tolerance, surface finish, and assembly fit.


