Continuous casting nozzles and tundishes can be reheated or baked again under appropriate conditions. However, the procedure depends on the refractory material, its condition after the initial heating, storage conditions, and equipment requirements.
For nozzles, the main considerations are refractory integrity, temperature changes, and heating uniformity. For tundishes, attention should be given to the condition of the refractory lining, moisture content, and temperature before casting.
Neither component should be subjected to a repeated heating cycle without checking the manufacturer's instructions and the applicable refractory heating procedure.
Can a continuous casting nozzle be baked a second time?
Yes, but the nozzle must first be inspected, and the refractory manufacturer's specifications must permit reheating.
A nozzle that has completed its initial baking but cannot be used because of production schedule changes, equipment failures, or other delays may require another heating cycle before use.
This is particularly relevant when the nozzle has been stored for an extended period, may have absorbed moisture from the surrounding environment, or has cooled significantly after its initial preheating. Its condition must be reassessed before it is installed for casting.
Precautions for a second heating cycle:
Inspect the nozzle condition: Check for cracks, impact damage, deformation, and other visible defects before reheating. A nozzle with significant refractory damage should not be considered suitable simply because it has been baked again.
Control the heating process: Nozzle materials and internal structures differ, so their heating schedules also vary. Some submerged entry nozzles require a specific rapid preheating procedure. Slow heating should not be applied as a universal rule. Excessively rapid heating can cause thermal stress damage, while insufficient heating or an unsuitable holding period can also affect nozzle performance.
Follow the manufacturer's procedure: The heating temperature, heating rate, holding time, and preheating equipment must be selected according to the technical specifications of the particular nozzle. Parameters for another material or model should not be used without verification.
Manage the waiting period before casting: After preheating, the nozzle should be maintained at an appropriate temperature according to the production schedule. Prolonged cooling or exposure to moisture should be avoided.
Can a continuous casting tundish be baked a second time?
Yes. A tundish can be dried or reheated again when necessary, depending on the condition of its refractory lining.
For example, a tundish may complete its initial baking but remain unused because of production scheduling, equipment maintenance, or other delays. If the lining has cooled or absorbed moisture during storage, its drying condition should be checked before reuse. A further drying or preheating cycle can then be arranged according to the actual condition.
Tundish reheating is intended not only to remove residual moisture where necessary, but also to bring the lining to the required temperature before casting. This helps reduce heat loss and temperature fluctuations when molten steel enters the tundish.
Precautions for a second heating cycle:
Inspect the refractory lining: Check the working lining, permanent lining, and other refractory components for visible cracks, spalling, delamination, or other damage. Remove any foreign materials and inspect the relevant nozzles and flow control components.
Set the heating schedule according to the lining material: Refractory materials differ in moisture content, thickness, and structure. Their drying time and heating rates therefore vary. Newly installed linings containing moisture require controlled drying according to the material specifications. A tundish that has already been dried but has cooled during a production delay may instead require reheating according to the preheating procedure.
Control the heating rate and holding time: Heating too quickly can prevent moisture inside the lining from escaping gradually. The resulting steam pressure may cause cracking or explosive spalling. An insufficient holding period can also leave the lining incompletely dried.
Check the thermal condition before use: After heating, confirm that the lining has reached the required process condition. Maintain an appropriate temperature according to the production schedule to prevent further cooling from affecting the casting operation.
Tundish drying and preheating are two different operations. Drying removes moisture from a newly installed refractory lining and generally requires a controlled heating process. Preheating before casting raises the tundish temperature to reduce heat loss from the molten steel. The appropriate procedure depends on the lining material and its actual condition.
Main differences between reheating nozzles and tundishes
Although both nozzles and tundishes contain refractory materials, their heating requirements are different.
For nozzles, the main concerns are structural integrity, uniform preheating, and the temperature immediately before casting. Excessive temperature differences can cause thermal stress and damage the refractory structure.
For tundishes, the main concerns are lining dryness, the condition of the working and permanent layers, and whether the overall temperature meets casting requirements.
For either component, inspect its condition first and then determine the heating procedure according to the refractory manufacturer's recommendations. The original heating schedule should not automatically be repeated without checking whether it is appropriate for the second heating cycle.
Custom machining of components for continuous casting equipment
The installation and maintenance of nozzles and tundishes also involve mechanical components such as nozzle mounting structures, support parts, transmission components, and other equipment fittings. Different machine designs have different dimensional and installation requirements, and some parts need custom machining to match their operating conditions.
We provide precision machining based on customer-supplied drawings and support both single-piece and small-batch orders. Hansheng Automation machines equipment mounting structures, shafts, transmission components, and other non-standard mechanical parts.
Our precision machining services also cover other industries, including precision structural components for yacht equipment, RC racing car parts, tobacco packaging machinery components, and parts for filling machinery. We manufacture non-standard components according to customer drawings for different equipment applications.


